?
Electro-Thermal Modeling of Trench-Isolated SiGe HBTs Using TCAD
P. 172–175.
Petrosyants K. O., Torgovnikov R.
In book
San Jose: the Institute of Electrical and Electronics Engineers, Inc., 2015.
Goltsman G., Александр С., IEEE Transactions on Applied Superconductivity 2023 P. 1–5
We investigate dark counts in SNSPD with spatial resolution, using nanostrip-patterned devices with 50 Ohm matched coplanar waveguide - tapers. We found that the dark counts originate from one or several points along the strip, which we call 'weak points'. We found that the dark counts originating from different points can have different dependence of ...
Added: May 7, 2024
A.S. Dragunova, N.V. Kryzhanovskaya, F. I. Zubov et al., St. Petersburg Polytechnical University Journal: Physics and Mathematics 2023 Vol. 16 No. 1.2 P. 108–113
In this work, we study the characteristics of semiconductor microlasers based on the heterostructure with two coupled waveguides intended to improve heat dissipation in cw regime. We analysed total output optical loss of the microlasers, their spectral characteristics, output power, emission pattern and thermal resistance. We observed that the use of the principle of two ...
Added: July 3, 2023
Ter-Zakaryan K. A., Zhukov A. D., Bobrova E. Yu. et al., Polymers 2021 Vol. 13 No. 21 Article 3698
Abstract: The application of foamed polymers as one of the components of insulating coatings allows to solve the problems of energy saving and creation of optimal operating conditions for constructions. The systems of application of energy-efficient heat-insulating materials must consider both the particularities of the insulating materials and the functional orientation of the constructions. The ...
Added: March 21, 2023
Mamontov A. V., Nefedov V. N., Khritkin S. A., Измерительная техника 2022 № 6 С. 46–51
The actual problem of accelerating and reducing the energy costs of the sheet polymer composite material heat treatment technological process is considered. It is shown that to solve this problem, it is advisable to use the microwave radiation energy as a heating source. The main advantages of the microwave method of the sheet polymer composite ...
Added: October 24, 2022
Kryzhanovskaya N., Dragunova A., Fominykh N. et al., , in: 2022 International Conference Laser Optics (ICLO).: IEEE, 2022. P. 1–1.
We discuss the static characteristics and high-frequency performance of microdisk lasers with an active region based on dense array of InGaAs/GaAs quantum well-dots having the improved thermal resistance. The decrease in thermal resistance of the microlasers is achieved by epi-side down bonding on a heat-conducting Si substrate. Compared to the characteristics of initial microlasers, the ...
Added: September 27, 2022
F I Zubov, E I Moiseev, A M Nadtochiy et al., Semiconductor Science and Technology 2022 Vol. 37 No. 7 Article 075010
Epi-side down bonding on a silicon substrate of AlGaAs/GaAs microdisk lasers is presented. A heterostructure with coupled large optical cavities enables location of an InGaAs quantum dot active region at a distance of ∼1 µm from the heterostructure surface. The thermal resistance was reduced to 0.2 and 0.1 K/mW for disks of 30 and 50 µm in diameter, ...
Added: July 12, 2022
Mamontov A. V., Nefedov V. N., Nazarov I. et al., Measurement Techniques 2021 Vol. 64 No. 4 P. 314–318
This paper addresses the high-priority goal of reducing the energy cost of heat-treating foam concrete slabs. We show that this problem is best solved using microwaves as a heat source. We discuss the main advantages of microwave curing over traditional techniques for curing foam concrete slabs, and develop a design for a microwave foam concrete ...
Added: October 16, 2021
Konstantin O. Petrosyants, Nikita I. Ryabov, , in: 2020 26th International Workshop on Thermal Investigations of ICs and Systems (THERMINIC).: IEEE, 2020. P. 1–7.
Multi-chip embedded PCBs were in resent years the mainstream technology of electronic packaging size reduction and at the same time providing improved performance. Ultra-small package size obviously strongly impacts the SiP module thermal behaviour. Unfortunately the complete thermal design methodology was not developed for this technology till now. In this work the problem of thermal ...
Added: June 5, 2021
Ismail-zade M. R., Petrosyants K. O., Sambursky L. M. et al., , in: 2020 26th International Workshop on Thermal Investigations of ICs and Systems (THERMINIC).: IEEE, 2020. P. 97–103.
A set of modified compact SPICE models of various flavours of MOSFETs (fabricated by bulk, SOI and SOS technologies) is presented for circuit simulation in the deep-cryogenic temperature range down to 4 K, which is important for space applications and development of scalable quantum computers. All models are constructed using the approach combining macromodeling based ...
Added: June 5, 2021
Mamontov A. V., Nefedov V. N., Nazarov I. et al., Измерительная техника 2021 № 4 С. 44–48
The actual problem of accelerating and reducing the energy costs of the foam concrete slabs heat treatment technological process is considered. It is shown that to solve this problem, it is advisable to use the microwave radiation energy as a heat source. The main advantages of the microwave method of foam concrete slabs heat treatment ...
Added: May 15, 2021
Nefedov V. N., Measurement Techniques 2019 Vol. 62 No. 5 P. 449–454
A method for the construction of microwave devices with longitudinal interaction is proposed. Devices of the present type create uniform cross-sectional distribution of temperature of rods made of polymer composite materials. Results from theoretical and experimental investigations of the cross-sectional distribution of the temperature of the material of the rod as well as the parameters ...
Added: December 2, 2019
Mamontov A. V., Nefedov V. N., Khritkin S. A., Measurement Techniques 2019 Vol. 62 No. 4 P. 365–370
We propose a method for designing transversely illuminated traveling-wave microwave devices. Devices of this type produce a uniform 3D temperature distribution in a polymer-composite rod. We describe theoretical and experimental results from studies of the 3D temperature distribution in the rod, along with the advantages of microwave curing technology over traditional curing techniques for polymer ...
Added: September 9, 2019
Nefedov V. N., Banov D. K., Bushuev V. D., , in: 2018 International Conference on Actual Problems of Electron Devices Engineering (APEDE).: Саратов: IEEE, 2018. P. 381–386.
The main parameters of beam-type microwave installation with frequency of the electromagnetic field oscillations 2450 MHz, the microwave output power of 4,8 kW for the heat treatment of a carbon fiber parabolic antenna, with heat-resistant epoxy binder, of the aperture diameter 1200 mm, thickness 5 mm are presented. The main results of the temperature distribution ...
Added: October 31, 2018
Nefedov V. N., Махмудов С. А., , in: 2018 International Conference on Actual Problems of Electron Devices Engineering (APEDE).: Саратов: IEEE, 2018. P. 376–380.
A model and method for calculating the temperature distribution of a wide range of materials in a microwave beam-type unit taking into account the reflective walls of the chamber is supposed. The experimental and modeling characteristics of the temperature distribution over the thickness of a homogeneous dielectric material at different distances from the walls of ...
Added: October 30, 2018
Nefedov V. N., Afanas'ev V. V., Ryabikina I. G., , in: 2018 International Conference on Actual Problems of Electron Devices Engineering (APEDE).: Саратов: IEEE, 2018. P. 371–375.
The results of the microwave radiation influence of the electromagnetic field oscillation frequency of 2450 MHz on the process of curing thermosetting epoxy resins, which are used as a binder in the production of polymer composite materials based on basalt, glass and carbon fibers, are presented. It is shown that the density of the cured ...
Added: October 30, 2018
Nefedov V. N., Mamontov A. V., Simonov V. et al., Measurement Techniques 2018 Vol. 61 No. 3 P. 265–270
A method is proposed for constructing radial type microwave devices forming a uniform temperature distribution throughout the volume of pipes made of polymer composite materials The results of theoretical and experimental investigations of the temperature distribution across the thickness of the pipe material are given. The advantages of microwave technologies for curing polymer composite aterials ...
Added: October 9, 2018
Nefedov V. N., Мамонтов А. В., Simonov V. et al., Измерительная техника 2018 № 3 С. 42–46
The method of construction of the radial type microwave devices forming the uniform temperature distribution in the volume of polymer composite pipes is suggested. The results of theoretical and experimental studies of the temperature distribution along the thickness of the pipe material are presented. The advantages of microwave technology for the curing of polymeric composite ...
Added: April 16, 2018
Nefedov V. N., Mamontov A. V., Simonov V. et al., T-Comm: Telecommunications and transport 2017 Vol. 11 No. 2 P. 52–55
Theoretical results of curing antennas made of composite materials using electromagnetic field of super high frequencies as a source of heat energy are presented. The advantages of microwave heat treatment of the antenna made of carbon fiber with epoxy binder in comparison with traditional methods are presented. Results of theoretical studies on the accelerated curing ...
Added: July 19, 2017
Nefedov V. N., Mamontov A. V., Simonov V. et al., T-Comm: Телекоммуникации и транспорт 2016 Т. 10 № 9 С. 5–8
Представлены теоретические результаты отверждения параболической антенны из полимерных композиционных материалов с использованием в качестве источника тепла энергии электромагнитного поля сверхвысоких частот. Показаны преимущества микроволнового метода тепловой обработки антенн из углеродного волокна с эпоксидным термоотверждающимся связующим по сравнению с традиционными методами. Приведены результаты теоретических исследований по ускоренному отверждению антенн из полимерных композиционных материалов в микроволновой установке ...
Added: July 19, 2017
Nefedov V. N., Mamontov A. V., Simonov V., Measurement Techniques 2016 Vol. 59 No. 8 P. 856–860
A design is proposed for microwave systems which produce a uniform temperature distribution over the transverse cross section of dielectric pipes. A method for calculating the temperature distribution over the thickness of pipes made of composite materials is examined. ...
Added: December 5, 2016
Nefedov V. N., Mamontov A. V., Chechetkin A. A., , in: 2016 International Conference on Actual Problems of Electron Devices Engineering (APEDE).: Саратов: IEEE, 2016. P. 456–462.
The method of calculation of the temperature distribution in the dielectric material for the traveling wave microwave devices is presented. The basic equations for the temperature distribution in the direction of the electromagnetic field energy propagation with considering the dependence of the dielectric parameters of a material on the temperature changes and taking into account ...
Added: October 24, 2016
Nefedov V. N., Mamontov A. V., Saygin I., , in: 2016 International Conference on Actual Problems of Electron Devices Engineering (APEDE).: Саратов: IEEE, 2016. P. 436–441.
The results of theoretical and experimental research in the field of high-performance microwave technology for the heat treatment of core material with low thermal conductivity are presented. The microwave method allows uniform heating of the dielectric rod throughout the volume, leads to the completeness of the polymerization reaction and high strength characteristics of the resulting ...
Added: October 24, 2016
Измерение температуры стенок композитных труб при термообработке в СВЧ-установках типа бегущей волны
Nefedov V. N., Mamontov A. V., Simonov V., Измерительная техника 2016 № 8 С. 45–48
Предложен метод построения микроволновых установок, формирующих равномерное распределение температуры по поперечному сечению диэлектрических труб. Рассмотрен способ расчёта распределения температуры по толщине труб из полимерных композиционных материалов. ...
Added: September 15, 2016