?
Research of Surface Wear Resistance of Aluminum Alloy Modified with Minerals using Sclerometry Method
Devices and Methods of Measurements (Belarus). 2019. Vol. 10. No. 3. P. 263–270.
A comparative study of the wear resistance, hardness and modulus of elasticity of ENAW-2024 aluminum alloy samples with and without a mineral coating was carried out. The wear resistance of the samples was studied by the method of multi-cycle friction, which makes it possible to measure the physicomechanical properties of thin modified material layers at the nanoscale. After the modification of the sample surface, the surface hardness and elastic modulus decreased by 20–36% and by 22–38%, respectively. At the same time, the wear resistance of the surface of the sample, modified by minerals, increased by more than 12 times compared with the wear resistance of the surface without modification. The parameters of the modified surface of the aluminum alloy, measured by sclerometry, can be further used to construct models of the surface modified by ultrafine mineral particles and to calculate the processes of friction and wear.
Economies 2026 Vol. 14 No. 07 P. 277
The increasingly rapid process of de-dollarization in the context of growing geopolitical fragmentation has significantly altered the monetary dynamics of the global economy, thereby posing important questions about economic resilience and sustainable development in the emerging world. This research investigates de-dollarization-related macro-financial conditions and their association with economic resilience in the BRICS+ countries during the ...
Added: July 14, 2026
Г. Г. Бондаренко, Кристя В. И., Савичкин Д. О. et al., Поверхность. Рентгеновские, синхротронные и нейтронные исследования 2026 № 4 С. 29–36
Сформулирована модель тлеющего газового разряда в смеси аргона и паров ртути при наличии
на поверхности катода тонкой диэлектрической пленки. Рассчитаны зависимости характеристик
разряда от температуры в интервале ее изменения, в котором заметный вклад в ионизацию
рабочей газовой смеси дает ионизация атомов ртути метастабильными возбужденными атомами
аргона (реакция Пеннинга). Показано, что в случае катода без диэлектрической пленки при
повышении температуры до ...
Added: June 20, 2026
Zirnik G., Ostovari Moghaddam A., Zhukov S. et al., Journal of Materials Science: Materials in Electronics 2026 Vol. 37 Article 738
In regards to the advances in InGaZnO for flexible transistors applications, herein for the first time we measure the broadband radio-frequency range (10 Hz to 1 MHz) dielectric permittivity ε′ and electrical conductivity σ of InGaZnO4 nanoparticle layers at different temperatures ranging from 10 to 300 K. The InGaZnO4 nanoparticles prepared by metal–nitrate–glycol gel decomposition method exhibited ...
Added: June 6, 2026
Das A., Saikia J., Maji N. et al., ChemNanoMat 2026 Vol. 12 No. 5 Article e202500733
Developing efficient photoactive materials from bio-derived resources is vital yet challenging for achieving effective water splitting performance. In this work, nano carbon dots (CDs) of zero-dimensional (0D) were synthesized from papaya peel through a simple and eco-friendly process and subsequently anchored onto the two-dimensional (2D) layered structure of graphitic carbon nitride (g-C3N4, GCN) at various ...
Added: June 2, 2026
Wary R. R., Mahato B., Sharma N. et al., The Journal of Physical Chemistry Letters 2026 Vol. 17 No. 17 P. 5099–5107
Development of heterojunction materials is an efficient approach for enhancing photocatalytic and photoelectrochemical processes. We develop a ZnO/CuO heterojunction via Cu doping into a ZnO matrix. Structural characterization confirmed that Cu was effectively incorporated into ZnO without any structural changes. The improved optical properties and reduced charge carrier recombination of the doped samples were confirmed ...
Added: June 2, 2026
Duran E. ., Pulgar A., Izquierdo R. et al., Physica Status Solidi (A) Applications and Materials 2026 Vol. 223 No. 7 Article e202500942
Ceramic superconductors exhibit remarkable properties, including zero electrical resistance and potent magnetic behavior, operating at temperatures as high as the boiling points of liquid nitrogen (77 K) and liquid hydrogen (20 K). These characteristics position them as key enablers for sustainable technologies spanning electric propulsion, lossless energy transmission, advanced medical imaging, and quantum computation. This review presents ...
Added: June 1, 2026
Андреев Д. В., Корнев С. А., Bondarenko G. et al., Перспективные материалы 2026 № 6 С. 5–11
Выполнено сравнительное исследование процессов сильнополевой зарядовой
деградации подзатворного диэлектрика структур металл-диэлектрик-полупроводник (МДП)
с алюминиевым и поликремниевым затвором. Зарядовые явления в МДП-структурах
изучали методом сильнополевой инжекции электронов в диэлектрик в режиме возрастания
плотности стрессового инжекционного тока с кратковременными переключениями
в измерительный режим при постоянной низкой плотности инжекционного тока.
Использование данного метода позволило получить новые данные о процессах зарядовой
деградации подзатворного диэлектрика МДП-структур с ...
Added: May 21, 2026
Rathish S., Andrey S. Vasenko, Thazhathenair A. et al., The Journal of Physical Chemistry Letters 2026 Vol. 17 No. 18 P. 5386–5394
We demonstrate and rationalize the effect of Au nanoparticles (NPs) on the hierarchical g-C3N4/CeO2 heterojunction. g-C3N4/CeO2 decorated with monodispersed plasmonic Au NPs was synthesized. Detailed analyses showed that CeO2 nanocubes and monodispersed Au NPs were evenly distributed over the 2D g-C3N4 surface, forming a robust interface enriched with abundant active sites. The structure enabled efficient separation of photogenerated charge ...
Added: May 16, 2026
Paul R., Das A., Sharma N. et al., Colloids and Surfaces A: Physicochemical and Engineering Aspects 2026 Vol. 728 Article 138830
Niobium-doped TiO2 (Nb-TiO2), demonstrates dual functionality as an efficient photocatalyst for dye degradation and a promising photoelectrocatalyst for water oxidation. Nb incorporation via a facile hydrothermal method was confirmed by XRD (Rietveld refinement), XPS, TEM, FT-IR, Raman, and BET analyses, indicating successful lattice doping and structural modification. Photocatalytic dye degradation experiments were conducted using a model ...
Added: May 16, 2026
Гущина В. А., / Series chemrxiv-2023-vpzhz-v2 "ChemRxiv". 2023.
All-inorganic perovskite CsPbBr3 and Cs4PbBr6 nanoparticles are being intensively studied due to their unique properties and wide range of applications; however, however, the nature of their optical properties is not yet fully understood due to the difficulty of synthesis of singlephase nanoparticles. In this article we describe the features of the synthesis of single-phase particles ...
Added: May 14, 2026
Гущина В. А., Mendeleev Communications 2025 Vol. 35 No. 2 P. 193–195
All-inorganic perovskite CsPbBr3 and Cs4PbBr6 nanoparticles are intensively studied for their unique optical properties, though synthesizing single-phase nanoparticles has posed challenges. Detailed synthesis method of CsPbBr3 and Cs4PbBr6 single-phase nanoparticles and their chemical and phase analysis are described. Distinctive optical characteristics, such as photoluminescence, optical band gap and the Urbach tail region, are revealed and explained within the current ...
Added: May 14, 2026
Гущина В. А., Physics of Complex System 2026 Vol. 7 No. 1 P. 3–15
Heterostructures based on ZnO nanorods and CsPbBr3 nanocrystals were investigated for their potential as semiconductor SERS substrates. We found that ZnO morphology governs the efficiency of interfacial energy transfer, leading to enhanced photoluminescence under 390 nm excitation and a noticeable reduction of the bandgap in the composites. Raman analysis revealed a pronounced intensity enhancement and ...
Added: May 14, 2026
Гущина В. А., Russian Journal of Inorganic Chemistry 2024 Vol. 69 No. 6 P. 940–948
Currently, ABX3 nanoparticles (NPs) based on lead halides attract the attention due to their unique optical properties and a wide range of applications. The preparation of NPs with lead as a partial or complete replacement is particularly interesting because of the toxicity of this chemical element and most of its compounds. In this study, we propose a ...
Added: May 6, 2026
Yasnitsky L., Голдобин М. А., Мезенцев А. С., Прикладная математика и вопросы управления 2025 № 2 С. 99–116
Представлен обзор современных методов и основанных на них программных
инструментах, применяемых для математического моделирования серийных производственных процессов с целью снижения брака и повышения качества производимых изделий. Перечисляются группы работ, нацеленных на обнаружение и классификацию дефектов, работ, в которых решаются задачи прогнозирования образования дефектов и определения значимости параметров, работ направленных на поиск
оптимального сочетания технологических параметров изготовления изделий, ...
Added: May 5, 2026
Morozov E. V., Demin A. S., Borovitskaya I. V. et al., Inorganic Materials: Applied Research 2026 Vol. 17 No. 3 P. 619–626
This article presents the results of experiments on the impact of powerful pulsed ion-plasma and
electron flows generated in the working chamber of the Plasma Focus PF-5M installation during each highvoltage
discharge on a model aluminum alloy B95. It is shown that the general characteristics of the alloy’s
damage upon exposure to pulsed flows of helium ions (HI) ...
Added: May 4, 2026
Pilé I., Deng Y., Shchur L., / Series arXiv "math". 2026. No. 2604.10254.
We investigate the spatial overlap of successive spin configurations in Markov chain Monte Carlo simulations using the local Metropolis algorithm and the Svendsen-Wang and Wolff cluster algorithms. We examine the dynamics of these algorithms for two models in different universality classes: the Ising model and the Potts model with three components. The overlap of two ...
Added: April 20, 2026
Pavlenko V. I., Bondarenko G.G., Cherkashina N. I. et al., Inorganic Materials: Applied Research 2026 Vol. 17 No. 2 P. 276–282
A composite material based on polyethylene, boron carbide (B4C), and bismuth oxide (Bi2O3) is
synthesized by the method of joint cryogenic milling of all components in liquid nitrogen environment followed
by pressing. The effect of cryogenic milling on the distribution of fillers in a composite is studied and
the prospects of using this method are assessed in comparison ...
Added: April 9, 2026
Черкашина Н. И., Павленко В. И., Bondarenko G. et al., Перспективные материалы 2026 № 4 С. 14–26
В данной работе представлен синтез гибкого полимерного композита для защиты от радиации на основе каучуковой матрицы и оксидов редкоземельных металлов, таких как Dy2O3 и Gd2O3, предназначенного для создания радиационно-защитных экранов и средств индивидуальной защиты. Исследованы его физико-механические характеристики: составы с добавлением оксида диспрозия имеют плотность от 1,31 до 2,44 г/см3, предел прочности при растяжении от ...
Added: April 2, 2026
Skazochkin A. V., Bondarenko G., Kislov S. V. et al., Письма о материалах 2025 Vol. 15 No. 4 P. 277–283
The article presents the results of comparative studies of wear resistance of railway wheel samples with surface modification by ultrafine mineral powders and without modification. The tested samples are made of standard railway wheels made of CT2sp steel (ordinary quality carbon steel — an analogue of Q215 steel (China), A192 steel (USA), and RSt34–2 steel ...
Added: December 9, 2025
Морозов Е. В., Демин А. С., Боровицкая И. В. et al., Физика и химия обработки материалов 2025 № 3 С. 5–15
Представлены результаты экспериментов по воздействию на модельный алюминиевый
сплав В95 мощных импульсных ионно-плазменных и электронных потоков,
генерируемых в рабочей камере установки Плазменный фокус ПФ-5М при каждом
высоковольтном разряде. Показано, что к общим характеристикам повреждаемости
сплава при воздействии на него импульсных потоков ионов гелия (ИГ) и гелиевой
плазмы (ГП) и импульсного облучения пучками электронов с близкими значениями
плотности мощности и длительности импульсов ...
Added: October 12, 2025
Roghani H., Borhani E., Jafarian H. R. et al., Wear 2023 Vol. 526-527 Article 204895
In this research, AA1050/AA2024 layered composites were created through six cycles of the ARB process. In this direction, the effect of using the reinforcing nanoparticles and the initial aging process on the mechanical properties and microstructure were researched. Two sheets of AA1050 and one sheet of AA2024 alternatively were used to create the composite. Also, ...
Added: February 18, 2025
Samoilova O., Shaburova N., Samodurova M. et al., Journal of Thermal Spray Technology 2023 Vol. 32 No. 5 P. 1220–1229
In this work, the morphology, microstructure, and phase composition of Al0.25CoCrFeNiSi0.6 high-entropy alloy coating (HEAC) deposited on stainless steel by detonation spraying (DS) are investigated. The Al0.25CoCrFeNiSi0.6 HEA ingot was first prepared by induction melting and then crushed and ground to ≤ 100 µm using a planetary ball milling apparatus. Detonation spraying was carried out on a computerized ...
Added: February 18, 2025
Naseri M., Ahmad Ostovari Moghaddam, Shaburova N. et al., Materials Today Communications 2024 Vol. 38 Article 108036
In the present work, Al0.25CoCrFeNiCu and Al0.45CoCrFeNiSi0.45 high entropy alloys (HEAs) were fabricated by induction melting and then subjected to severe cold rolling (SCR) to induce an ultrafine lamellar microstructure. By using electron back scattered diffraction (EBSD) analysis, the microstructural features of the SCR processed HEAs were determined to be deformation bands, severely pancaked grains, and a refined lamellar microstructure. The ...
Added: January 23, 2025
Kagan M., Silkin V. M., Efremov D. V., / Series arXiv "math". 2024. No. 2411.12836.
In this study, we analyze the dielectric function of high-Tc cuprates as a function of doping level, taking into account the full energy band dispersion within the CuO2 monolayer. In addition to the conventional two-dimensional (2D) gapless plasmon mode, our findings reveal the existence of three anomalous branches within the plasmon spectrum. Two of these branches ...
Added: November 27, 2024