?
Influence of the Electric Field Enhanced Thermal Electron Emission on Temperature of the Cathode with a Thin Insulating Film in the Arc Gas Discharge
Technical Physics. 2020. Vol. 65. No. 5. P. 826–831.
A model of the electric field enhanced thermal (thermo-field) emission of electrons from the metal
cathode substrate into a thin insulating film on its surface is developed. A system of equations for the cathode
surface temperature in the arc discharge and the electric field strength in the film, providing the required discharge
current density, is formulated. It is shown that existence of the insulating film can result in a considerable
reduction of the cathode temperature in the discharge due to lower potential barrier height at the
metal-insulator boundary than at the metal-discharge boundary in case of the cathode without the film. It is
found that due to an enhancement of the thermal emission of electrons into the film by the electric field generated
in it, an additional decrease in the cathode temperature by about 100 K takes place.
Г. Г. Бондаренко, Кристя В. И., Савичкин Д. О. et al., Поверхность. Рентгеновские, синхротронные и нейтронные исследования 2026 № 4 С. 29–36
Сформулирована модель тлеющего газового разряда в смеси аргона и паров ртути при наличии
на поверхности катода тонкой диэлектрической пленки. Рассчитаны зависимости характеристик
разряда от температуры в интервале ее изменения, в котором заметный вклад в ионизацию
рабочей газовой смеси дает ионизация атомов ртути метастабильными возбужденными атомами
аргона (реакция Пеннинга). Показано, что в случае катода без диэлектрической пленки при
повышении температуры до ...
Added: June 20, 2026
Zirnik G., Ostovari Moghaddam A., Zhukov S. et al., Journal of Materials Science: Materials in Electronics 2026 Vol. 37 Article 738
In regards to the advances in InGaZnO for flexible transistors applications, herein for the first time we measure the broadband radio-frequency range (10 Hz to 1 MHz) dielectric permittivity ε′ and electrical conductivity σ of InGaZnO4 nanoparticle layers at different temperatures ranging from 10 to 300 K. The InGaZnO4 nanoparticles prepared by metal–nitrate–glycol gel decomposition method exhibited ...
Added: June 6, 2026
Das A., Saikia J., Maji N. et al., ChemNanoMat 2026 Vol. 12 No. 5 Article e202500733
Developing efficient photoactive materials from bio-derived resources is vital yet challenging for achieving effective water splitting performance. In this work, nano carbon dots (CDs) of zero-dimensional (0D) were synthesized from papaya peel through a simple and eco-friendly process and subsequently anchored onto the two-dimensional (2D) layered structure of graphitic carbon nitride (g-C3N4, GCN) at various ...
Added: June 2, 2026
Wary R. R., Mahato B., Sharma N. et al., The Journal of Physical Chemistry Letters 2026 Vol. 17 No. 17 P. 5099–5107
Development of heterojunction materials is an efficient approach for enhancing photocatalytic and photoelectrochemical processes. We develop a ZnO/CuO heterojunction via Cu doping into a ZnO matrix. Structural characterization confirmed that Cu was effectively incorporated into ZnO without any structural changes. The improved optical properties and reduced charge carrier recombination of the doped samples were confirmed ...
Added: June 2, 2026
Duran E. ., Pulgar A., Izquierdo R. et al., Physica Status Solidi (A) Applications and Materials 2026 Vol. 223 No. 7 Article e202500942
Ceramic superconductors exhibit remarkable properties, including zero electrical resistance and potent magnetic behavior, operating at temperatures as high as the boiling points of liquid nitrogen (77 K) and liquid hydrogen (20 K). These characteristics position them as key enablers for sustainable technologies spanning electric propulsion, lossless energy transmission, advanced medical imaging, and quantum computation. This review presents ...
Added: June 1, 2026
Андреев Д. В., Корнев С. А., Bondarenko G. et al., Перспективные материалы 2026 № 6 С. 5–11
Выполнено сравнительное исследование процессов сильнополевой зарядовой
деградации подзатворного диэлектрика структур металл-диэлектрик-полупроводник (МДП)
с алюминиевым и поликремниевым затвором. Зарядовые явления в МДП-структурах
изучали методом сильнополевой инжекции электронов в диэлектрик в режиме возрастания
плотности стрессового инжекционного тока с кратковременными переключениями
в измерительный режим при постоянной низкой плотности инжекционного тока.
Использование данного метода позволило получить новые данные о процессах зарядовой
деградации подзатворного диэлектрика МДП-структур с ...
Added: May 21, 2026
Rathish S., Andrey S. Vasenko, Thazhathenair A. et al., The Journal of Physical Chemistry Letters 2026 Vol. 17 No. 18 P. 5386–5394
We demonstrate and rationalize the effect of Au nanoparticles (NPs) on the hierarchical g-C3N4/CeO2 heterojunction. g-C3N4/CeO2 decorated with monodispersed plasmonic Au NPs was synthesized. Detailed analyses showed that CeO2 nanocubes and monodispersed Au NPs were evenly distributed over the 2D g-C3N4 surface, forming a robust interface enriched with abundant active sites. The structure enabled efficient separation of photogenerated charge ...
Added: May 16, 2026
Paul R., Das A., Sharma N. et al., Colloids and Surfaces A: Physicochemical and Engineering Aspects 2026 Vol. 728 Article 138830
Niobium-doped TiO2 (Nb-TiO2), demonstrates dual functionality as an efficient photocatalyst for dye degradation and a promising photoelectrocatalyst for water oxidation. Nb incorporation via a facile hydrothermal method was confirmed by XRD (Rietveld refinement), XPS, TEM, FT-IR, Raman, and BET analyses, indicating successful lattice doping and structural modification. Photocatalytic dye degradation experiments were conducted using a model ...
Added: May 16, 2026
Гущина В. А., / Series chemrxiv-2023-vpzhz-v2 "ChemRxiv". 2023.
All-inorganic perovskite CsPbBr3 and Cs4PbBr6 nanoparticles are being intensively studied due to their unique properties and wide range of applications; however, however, the nature of their optical properties is not yet fully understood due to the difficulty of synthesis of singlephase nanoparticles. In this article we describe the features of the synthesis of single-phase particles ...
Added: May 14, 2026
Гущина В. А., Mendeleev Communications 2025 Vol. 35 No. 2 P. 193–195
All-inorganic perovskite CsPbBr3 and Cs4PbBr6 nanoparticles are intensively studied for their unique optical properties, though synthesizing single-phase nanoparticles has posed challenges. Detailed synthesis method of CsPbBr3 and Cs4PbBr6 single-phase nanoparticles and their chemical and phase analysis are described. Distinctive optical characteristics, such as photoluminescence, optical band gap and the Urbach tail region, are revealed and explained within the current ...
Added: May 14, 2026
Гущина В. А., Physics of Complex System 2026 Vol. 7 No. 1 P. 3–15
Heterostructures based on ZnO nanorods and CsPbBr3 nanocrystals were investigated for their potential as semiconductor SERS substrates. We found that ZnO morphology governs the efficiency of interfacial energy transfer, leading to enhanced photoluminescence under 390 nm excitation and a noticeable reduction of the bandgap in the composites. Raman analysis revealed a pronounced intensity enhancement and ...
Added: May 14, 2026
Гущина В. А., Russian Journal of Inorganic Chemistry 2024 Vol. 69 No. 6 P. 940–948
Currently, ABX3 nanoparticles (NPs) based on lead halides attract the attention due to their unique optical properties and a wide range of applications. The preparation of NPs with lead as a partial or complete replacement is particularly interesting because of the toxicity of this chemical element and most of its compounds. In this study, we propose a ...
Added: May 6, 2026
Yasnitsky L., Голдобин М. А., Мезенцев А. С., Прикладная математика и вопросы управления 2025 № 2 С. 99–116
Представлен обзор современных методов и основанных на них программных
инструментах, применяемых для математического моделирования серийных производственных процессов с целью снижения брака и повышения качества производимых изделий. Перечисляются группы работ, нацеленных на обнаружение и классификацию дефектов, работ, в которых решаются задачи прогнозирования образования дефектов и определения значимости параметров, работ направленных на поиск
оптимального сочетания технологических параметров изготовления изделий, ...
Added: May 5, 2026
Morozov E. V., Demin A. S., Borovitskaya I. V. et al., Inorganic Materials: Applied Research 2026 Vol. 17 No. 3 P. 619–626
This article presents the results of experiments on the impact of powerful pulsed ion-plasma and
electron flows generated in the working chamber of the Plasma Focus PF-5M installation during each highvoltage
discharge on a model aluminum alloy B95. It is shown that the general characteristics of the alloy’s
damage upon exposure to pulsed flows of helium ions (HI) ...
Added: May 4, 2026
Bondarenko G.G., Fisher M. R., Kristya V. I., Bulletin of the Russian Academy of Sciences: Physics 2026 Vol. 90 No. 4 P. 572–576
A model of the cathode layer of a glow gas discharge with a thin dielectric film on a fraction of the
cathode’s working surface is formulated. It is shown that a glow discharge most rapidly transits to an arc discharge,
accompanied by a significant increase in discharge current density and a decrease in cathode voltage
drop, if the ...
Added: April 25, 2026
Pilé I., Deng Y., Shchur L., / Series arXiv "math". 2026. No. 2604.10254.
We investigate the spatial overlap of successive spin configurations in Markov chain Monte Carlo simulations using the local Metropolis algorithm and the Svendsen-Wang and Wolff cluster algorithms. We examine the dynamics of these algorithms for two models in different universality classes: the Ising model and the Potts model with three components. The overlap of two ...
Added: April 20, 2026
Pavlenko V. I., Bondarenko G.G., Cherkashina N. I. et al., Inorganic Materials: Applied Research 2026 Vol. 17 No. 2 P. 276–282
A composite material based on polyethylene, boron carbide (B4C), and bismuth oxide (Bi2O3) is
synthesized by the method of joint cryogenic milling of all components in liquid nitrogen environment followed
by pressing. The effect of cryogenic milling on the distribution of fillers in a composite is studied and
the prospects of using this method are assessed in comparison ...
Added: April 9, 2026
Черкашина Н. И., Павленко В. И., Bondarenko G. et al., Перспективные материалы 2026 № 4 С. 14–26
В данной работе представлен синтез гибкого полимерного композита для защиты от радиации на основе каучуковой матрицы и оксидов редкоземельных металлов, таких как Dy2O3 и Gd2O3, предназначенного для создания радиационно-защитных экранов и средств индивидуальной защиты. Исследованы его физико-механические характеристики: составы с добавлением оксида диспрозия имеют плотность от 1,31 до 2,44 г/см3, предел прочности при растяжении от ...
Added: April 2, 2026
Chowde Gowda C., Alexey Kartsev, Tiwari N. et al., Journal of Materials Chemistry C 2024 Vol. 12 No. 46 P. 18691–18703
Two-dimensional (2D) chromium telluride Cr2Te3 exhibits strong ferromagnetic ordering with high coercivity at low temperatures and paramagnetic behavior when approaching room temperature. The spin states of monolayer Cr2Te3 show ferromagnetic ordering in the ground state. In situ Raman analysis reveals a reversible structure transformation and hence proves ferromagnetic to paramagnetic transition during low-temperature heating cycles (0–25 °C). The magnetic ...
Added: March 16, 2026
Li L., Li Z., Meng J. et al., Chemical Communications 2025 Vol. 61 No. 45 P. 8252–8255
Sodium-ion batteries (SIBs) have emerged as a promising alternative to lithium-ion batteries due to the abundance and cost-effectiveness of sodium resources. However, their widespread application is hindered by challenges such as sluggish ion diffusion kinetics and structural instability of cathode materials during prolonged cycling. The design of advanced cathode architectures with enhanced ion transport and ...
Added: May 8, 2025
Bondarenko G., Фишер М. Р., Кристя В. И., Поверхность. Рентгеновские, синхротронные и нейтронные исследования 2025 № 1 С. 78–85
Представлена модель катодного слоя тлеющего газового разряда при наличии на катоде
диэлектрической пленки, толщина которой различна на разных участках его поверхности, причем
на части поверхности она может отсутствовать. Модель учитывает ионно-электронную эмиссию
с поверхности катода, термополевую электронную эмиссию из подложки катода в пленку
и термическую электронную эмиссию с участков катода без пленки. Показано, что при нагреве
катода эмиссионная эффективность пленки, ...
Added: May 6, 2025
Kagan M., Silkin V. M., Efremov D. V., / Series arXiv "math". 2024. No. 2411.12836.
In this study, we analyze the dielectric function of high-Tc cuprates as a function of doping level, taking into account the full energy band dispersion within the CuO2 monolayer. In addition to the conventional two-dimensional (2D) gapless plasmon mode, our findings reveal the existence of three anomalous branches within the plasmon spectrum. Two of these branches ...
Added: November 27, 2024
Influence of anisotropy on the study of critical behavior of spin models by machine learning methods
Sukhoverkhova D., Shchur L., / Series arXiv "math". 2024. No. 2410.14523.
In this paper, we applied a deep neural network to study the issue of knowledge transferability between statistical mechanics models. The following computer experiment was conducted. A convolutional neural network was trained to solve the problem of binary classification of snapshots of the Ising model's spin configuration on a two-dimensional lattice. During testing, snapshots of ...
Added: October 21, 2024
Mozolenko V., Fadeeva Marina, Shchur L., / Series arXiv "math". 2024. No. 2405.10865.
The development of new algorithms for simulations in physics is as important as the development of new analytical methods. In this paper we present a comparison of the recently developed microcanonical population annealing (MCPA) algorithm with the rather mature Wang-Landau algorithm. The comparison is performed on two cases of the Potts model exhibiting a first ...
Added: May 20, 2024