?
Влияние материала затвора МДП-структур на процессы сильнополевой зарядовой деградации подзатворного диэлектрика
Перспективные материалы. 2026. № 6. С. 5–11.
Mehrabi-Kalajahi S., Vasigh S. A., Yousefi Bavili H. et al., Scientific Reports 2026 Vol. 16 Article 20035
High-entropy oxides (HEOs) have recently gained considerable attention as next-generation electrocatalysts owing to their exceptional compositional flexibility, structural stability, and synergistic multimetal effects. In this study, a series of Cu-modified high-entropy oxide catalysts (HEO–Cu) with different Cu loadings (20%, 30%, 40%, 50%, and 60%) supported on nickel foam (NF) were synthesized via a facile co-precipitation ...
Added: November 4, 2026
Sabzi M., Abdollahzadeh A., Jafarian H. R. et al., International Journal of Pressure Vessels and Piping 2026 Vol. 225 Article 105979
This study investigates the microstructural evolution, hydrogen embrittlement (HE) susceptibility, and sour corrosion resistance of dissimilar A105 carbon steel/316L austenitic stainless steel welded joints representative of pipeline components produced by continuous (CCGTAW) and pulsed current gas tungsten arc welding (PCGTAW) with ER309L filler. Microstructural analysis revealed that pulsed arc thermal cycling promoted grain refinement, transitioning ...
Added: November 4, 2026
Кислов С. В., Сказочкин А. В., Bondarenko G., Фундаментальные и прикладные проблемы техники и технологии 2026 Т. 31 № 5 С. 96–107
В статье представлены результаты сравнительных исследований износостойкости образцов из железнодорожных колес - а) без покрытия и б) с поверхностным слоем,созданным по технологии минеральных покрытий. Тестируемые образцы были изготовлены из стандартных железнодорожных колес из стали СТ2 (Россия), а контрролики – из рельсовой стали Э76ХФ (Россия). На торцевой поверхности образцов были созданы слои, модифицированные ультрадисперсными частицами минералов. ...
Added: November 3, 2026
Бецофен С. Я., Осинцев О. Е., Кабанова Ю. А. et al., Вестник Московского авиационного института 2016 Т. 23 № 4 С. 181–188
Методами рентгеноструктурного анализа и механических испытаний на растяжение исследованы особенности формирования анизотропии механических свойств, текстуры и фазового состава тонколистовых сплавов Al–4,3Cu–1,4Li–0,4Mg и Al–1,8Li–1,8Cu–0,9Mg. Установлен различный тип анизотропии прочностных свойств сплавов: нормальный (прочность в долевом направлении выше, чем в поперечном) для сплава Al–4,3Cu–1,4Li–0,4Mg и обратный для сплава Al–1,8Li–1,8Cu–0,9Mg. Показано, что на анизотропию прочностных свойств влияет не ...
Added: October 21, 2026
Сказочкин А. В., Бондаренко Г.Г., Гайдар А. И. et al., Перспективные материалы 2026 № 11 С. 60–75
Рассмотрены механизмы структурно-фазовой перестройки и физико-химические
процессы при формировании износостойких и коррозионно-пассивных покрытий на
чугуне ВЧ40 комбинированной технологией, сочетающей ультразвуковое пластическое
деформирование и электроискровое легирование (ЭИЛ). Образцы модифицировали
ультразвуковым индентором (УЗИ) в среде микрочастиц SiO2 (5 мкм) под давлением
400 МПа с последующим ЭИЛ графитовым и твердосплавным (ВК8) электродом. Структуру,
состав и микротвердость изучали методами сканирующий электронный микроскопии
совмещенной с энергодисперсионной рентгеновской ...
Added: October 16, 2026
Тукачев Н. В., Akkuratov A., Nikitenko S. et al., Solar Energy 2020 Vol. 198 P. 605–611
One of the major challenges in the field of organic photovoltaics is associated with high-throughput manufacturing of efficient and stable organic solar cells. Practical realization of technologies for production of large-area organic solar cells requires the development of novel materials with a defined combination of properties ensuring sufficient reliability and scalability of the process in ...
Added: October 14, 2026
Liu X., Nikita Tukachev, Wang K. et al., INTERDISCIPLINARY MATERIALS 2026 Vol. 5 No. 1 P. 85–123
Hydrogen halide gases are one of the most wide-spread pollutants of atmosphere, which are generated by various industrial sectors or natural processes, and may dramatically affect human health above certain thresholds of exposure. Hence, it is critically important to develop effective sensing methods for these gases. Herein, we review the recent progress as well as ...
Added: October 14, 2026
Ostovari Moghaddam A., Mehrabi-Kalajahi S., Solizoda I. A. et al., Metals and Materials International 2026 Vol. 32 P. 3767–3775
Off-stoichiometric boron-doped chemically complex intermetallic alloys (CCIMAs) have recently emerged as a new avenue for overcoming the low temperature brittleness of ordered superlattices. However, their behavior at high temperatures remains unexplored. In this study, a novel (Ni39.6Co29.3Cr10Al15.8Ta3.3Nb2)98.5B1.5 CCIMA was prepared and its oxidation resistance over a wide temperature range (500 °C–950 °C) was studied. The ...
Added: October 1, 2026
Piliugin L., Antropov A., Lobashev E. et al., Journal of Nuclear Materials 2026 Vol. 632 Article 156876
The effects of dislocations on the mobility of gas nanobubbles pinned to them are considered as novel unex- plored mechanisms of accelerated fission gas release and investigated using classical molecular dynamics of helium bubbles in FCC aluminum. Non-equilibrium methods are developed to calculate the mobility of a pinned bubble both along and across the dislocation ...
Added: September 28, 2026
Li Y., Han J., Zaman N. et al., ACS Applied Materials & Interfaces 2026 Vol. 18 No. 39 P. 54241–54251
The development of lead sulfide (PbS) quantum dot (QD) photodetectors for short-wave infrared (SWIR) applications has been fundamentally limited by the thermodynamic instability of large PbS QD facets, which leads to aggregation and epitaxial fusion. In this work, robust thermodynamic stabilization was achieved by introducing methylammonium chloride (MACl) in PbS QD surface passivation, as validated ...
Added: September 26, 2026
Боровицкая И. В., Пименов В. Н., Коршунов С. Н. et al., Перспективные материалы 2026 № 10 С. 37–54
Проведено сравнение, обобщение и систематизация механизмов эрозии и разрушения
поверхности малоактивируемых материалов, перспективных для использования в
качестве материалов вакуумной камеры термоядерных реакторов: ванадия, его сплава
V – 10 Ti – 6 Cr – 0,05 Zr – 0,1 Si и вольфрама при последовательном воздействии на
них ионных и тепловых потоков. Тепловые потоки имитировали с помощью мощного
импульсного лазерного излучения (ЛИ), создаваемого ...
Added: September 22, 2026
Andreev D. V., Kornev S. A., Bondarenko G.G. et al., Inorganic Materials: Applied Research 2026 Vol. 17 No. 5 P. 1226–1230
Comparative studies are carried out to investigate high-field charge degradation effects in the gate
dielectric of metal—insulator—semiconductor (MIS) structures with aluminum and polysilicon gates.
Charging phenomena in MIS structures are explored using high-field electron injection into the dielectric
under conditions of gradually increasing voltage current density, with periodic short-term switching to a measurement
mode at a constant low injection ...
Added: September 15, 2026
Cherkashina N. I., Pavlenko V. I., Bondarenko G.G. et al., Inorganic Materials: Applied Research 2026 Vol. 17 No. 5 P. 1247–1257
The description is given to the synthesis of a flexible polymer composite for radiation protection
based on a rubber matrix and rare-earth metal oxides (Dy2O3 and Gd2O3). The physico-mechanical parameters
are established for the compositions with dysprosium oxide as follows: the density ranging from 1.31 to
2.44 g/cm3, tensile strength is staying between 6.06 and 1.72 MPa. In ...
Added: September 15, 2026
P. M. Marychev, A. A. Shanenko, Physical Review B: Condensed Matter and Materials Physics 2026 Vol. 114 No. 7 Article 074509
We investigate the effect of weak interband impurity scattering on the intertype (IT) domain between type-I and type-II superconductivity in diffusive two-band superconductors. Our results show that the significant broadening of the IT domain with increasing band diffusivity ratio, previously established in the absence of interband scattering, persists under weak interband scattering. However, depending on ...
Added: September 7, 2026
Tomayeva M., Vyacheslav D. Neverov, Arkady A. Shanenko et al., Physical Review B: Condensed Matter and Materials Physics 2026 Vol. 114 No. 2 Article 024516
We report a thermally driven structural crossover of vortex matter in a two-dimensional superconducting Penrose quasicrystal. At low temperatures, vortices are pinned by the quasiperiodic lattice, forming an aperiodic pattern. With increasing temperature, vortex-vortex interactions dominate, leading to a conventional triangular Abrikosov lattice. Our findings reveal a tunable interplay between intrinsic pinning and vortex interactions, ...
Added: September 5, 2026
Vyacheslav D. Neverov, Lukyanov A., Andrey V. Krasavin et al., Physical Review B: Condensed Matter and Materials Physics 2026 Vol. 113 No. 2 Article 024515
We develop a neural network approach to solve the self-consistent Bogoliubov-de Gennes equations in strongly disordered s-wave superconductors. The method accurately reproduces inhomogeneous gap distributions and generalizes to system sizes far larger than those used in training. It reduces computational scaling from O(N6 ) to O(N2), enabling quantitative analysis of percolation phenomena and the superconductor-insulator ...
Added: September 5, 2026
Бондаренко Г.Г., Фишер М. Р., Кристя В. И., Известия РАН. Серия физическая 2026 Т. 90 № 4 С. 867–874
Сформулирована модель катодного слоя тлеющего газового разряда при наличии на
части рабочей поверхности катода тонкой диэлектрической пленки. Показано, что переход тлеющего разряда в дуговой разряд, сопровождающийся значительным увеличением плотности разрядного тока и уменьшением катодного падения напряжения, происходит наиболее быстро, если
пленка занимает примерно половину поверхности катода. ...
Added: September 4, 2026
Danil Kobtsev, Jarashneli A., Maman N. et al., Applied Sciences (Switzerland) 2026 Vol. 16 No. 17 Article 8577
AIVBVI semiconductors, particularly lead chalcogenides, remain key materials for mid-wave infrared (MWIR) photodetection due to their narrow bandgap and exceptional carrier transport properties. However, the realization of high-quality p-type PbTe thin films, suitable for p–n junction devices, remains a technological challenge. In this work, we report the fabrication of high-mobility p-type PbTe thin films grown on ...
Added: August 30, 2026
G. G. Bondarenko, Kristya V. I., Savichkin D. O. et al., Journal of Surface Investigation: X-Ray, Synchrotron and Neutron Techniques 2026 Vol. 20 No. 2 P. 417–423
A model of a glow gas discharge in a mixture of argon and mercury vapor is formulated in the presence
of a thin insulating film on the cathode surface. Dependences of the discharge characteristics on the
mixture temperature are calculated in the range of its variation, in which a noticeable contribution to ionization
of the working gas is ...
Added: August 1, 2026
Dmitry Vasilyev, Gorev V., Ikhsanov R. et al., Journal of Materials Science 2026 No. 61 P. 25452–25470
The orthorhombic phase of 𝛼-Mo2 C is a key component in electrocatalytic applications, as Mo2C-based catalysts can exhibit catalytic performance comparable to or exceeding that of noble metals. Despite its technological relevance, theoretical understanding of the anisotropy in the thermal expansion and related thermoelastic properties of 𝛼-Mo2 C remains limited. In this work, first-principles calculations ...
Added: July 23, 2026
Borovitskaya I. V., Pimenov V. N., Korshunov S. N. et al., Physics of Atomic Nuclei 2026 Vol. 89 No. 1 P. S48–S55
The effect of high-power pulsed laser radiation (LR) generated in the GOS 1001 setup in the
Q-modulated mode (with a flux power density q equal to 1 × 1014 W/m2, pulse duration t = 50 ns, and the
number of pulses N from 1 to 8 in vacuum) on the structure and microhardness of the surface of ...
Added: July 22, 2026
Andreev D. V., Kornev S. A., G. G. Bondarenko et al., Inorganic Materials: Applied Research 2025 Vol. 16 No. 5 P. 1301–1305
Injection-thermal treatment (ITT) of MIS structures in the mode of stepwise increase in highfield
injection current density bounded by the value of Jb, at which no noticeable processes of irreversible
charge degradation of the gate dielectric and its interface with the semiconductor occur, is under consideration.
The charge density injected into the gate dielectric during ITT should provide ...
Added: September 12, 2025
Андреев Д. В., Корнев С. А., Bondarenko G. et al., Перспективные материалы 2025 № 5 С. 17–23
Рассмотрена инжекционно-термическая обработка (ИТО) МДП-структур в режиме
ступенчато-возрастающей плотности сильнополевого инжекционного тока, ограниченной
значением Jb, при которой не происходит заметных процессов необратимой зарядовой
деградации подзатворного диэлектрика и его границы раздела с полупроводником. Плотность
заряда, инжектированного в подзатворный диэлектрик при проведении ИТО, должна
обеспечивать выявление образцов с внешними дефектами. Установлено, что проведение
инжекционно-термической обработки позволяет существенно снизить плотность внешних
дефектов в диэлектрической пленке ...
Added: May 17, 2025
Andreev D., Gennady G. Bondarenko, Andreev V. et al., , in: Proceedings of 2022 IEEE Moscow Workshop on Electronic and Networking Technologies (MWENT).: M.: IEEE, 2022. P. 1–3.
In modern microelectronics high fields are an essential condition of devices based on metal-insulator-semiconductor (MIS) structures what is caused by downscaling of nodes of semiconductor manufacturing processes. Under these conditions, a possibility of charge degradation increases what can result in dielectric film breakdown and following integrated circuit (IC) failure. Therefore, a designing of configurable set ...
Added: August 31, 2022