?
Experimental examination of the chemical-metallurgical roasting process for iron ore raw materials on the fire grate of a roasting conveyor machine
CIS Iron and Steel Review. 2023. Vol. 26. P. 12–16.
Bobkov V. I., Dli M. I., Kulyasov N.S.
The results of experimental power engineering examination of operating roasting conveyor machines are presented. These machines are used for complicated energy-intensive chemical-metallurgical process of roasting of iron ore raw materials in moving dense layer with cross feed of heat-carrying gas. The studies were conducted within the temperature ranges of thermal and aerodynamic operating conditions of the existing roasting conveyor machines. The causes of insufficient power engineering efficiency of the chemical-metallurgical roasting process were revealed, qualitative analysis of thermal conditions of roasting dense layer of iron ore raw materials was carried out. The data on temperature distribution of heating gas and iron ore material in different areas of a dynamic dense layer and on a fire grate in different sections of the roasting machine were obtained. The experimental data from technological control of the roasting conveyor machine were presented, as well as the results of chemical and granulometric analyses of roasting iron ore raw materials. Essential deviations in the thermal conditions of operating roasting machine in comparison with designed parameters were found out. The data on roasting conditions of iron ore raw materials in the experimental unit – the sintering pan, which provides simulation of the roasting conditions close to designed ones, are displayed. Insufficient heating in the lower layer levels at the operating roasting machines (in comparison with the designed parameters), stipulated by low speed of heat-carrying gas sweeping in the roasting area was revealed. Temperature heterogeneity along the width of a fire grate, caused by heterogeneity of heat-carrying gas sweeping due to segregation of iron ore material by its size during its loading to the roasting conveyor machine was substantiated scientifically.
G. G. Bondarenko, Kristya V. I., Savichkin D. O. et al., Journal of Surface Investigation: X-Ray, Synchrotron and Neutron Techniques 2026 Vol. 20 No. 2 P. 417–423
A model of a glow gas discharge in a mixture of argon and mercury vapor is formulated in the presence
of a thin insulating film on the cathode surface. Dependences of the discharge characteristics on the
mixture temperature are calculated in the range of its variation, in which a noticeable contribution to ionization
of the working gas is ...
Added: August 1, 2026
Dmitry Vasilyev, Gorev V., Ikhsanov R. et al., Journal of Materials Science 2026 No. 61 P. 25452–25470
The orthorhombic phase of 𝛼-Mo2 C is a key component in electrocatalytic applications, as Mo2C-based catalysts can exhibit catalytic performance comparable to or exceeding that of noble metals. Despite its technological relevance, theoretical understanding of the anisotropy in the thermal expansion and related thermoelastic properties of 𝛼-Mo2 C remains limited. In this work, first-principles calculations ...
Added: July 23, 2026
Borovitskaya I. V., Pimenov V. N., Korshunov S. N. et al., Physics of Atomic Nuclei 2026 Vol. 89 No. 1 P. S48–S55
The effect of high-power pulsed laser radiation (LR) generated in the GOS 1001 setup in the
Q-modulated mode (with a flux power density q equal to 1 × 1014 W/m2, pulse duration t = 50 ns, and the
number of pulses N from 1 to 8 in vacuum) on the structure and microhardness of the surface of ...
Added: July 22, 2026
Economies 2026 Vol. 14 No. 07 P. 277
The increasingly rapid process of de-dollarization in the context of growing geopolitical fragmentation has significantly altered the monetary dynamics of the global economy, thereby posing important questions about economic resilience and sustainable development in the emerging world. This research investigates de-dollarization-related macro-financial conditions and their association with economic resilience in the BRICS+ countries during the ...
Added: July 14, 2026
Г. Г. Бондаренко, Кристя В. И., Савичкин Д. О. et al., Поверхность. Рентгеновские, синхротронные и нейтронные исследования 2026 № 4 С. 29–36
Сформулирована модель тлеющего газового разряда в смеси аргона и паров ртути при наличии
на поверхности катода тонкой диэлектрической пленки. Рассчитаны зависимости характеристик
разряда от температуры в интервале ее изменения, в котором заметный вклад в ионизацию
рабочей газовой смеси дает ионизация атомов ртути метастабильными возбужденными атомами
аргона (реакция Пеннинга). Показано, что в случае катода без диэлектрической пленки при
повышении температуры до ...
Added: June 20, 2026
Zirnik G., Ostovari Moghaddam A., Zhukov S. et al., Journal of Materials Science: Materials in Electronics 2026 Vol. 37 Article 738
In regards to the advances in InGaZnO for flexible transistors applications, herein for the first time we measure the broadband radio-frequency range (10 Hz to 1 MHz) dielectric permittivity ε′ and electrical conductivity σ of InGaZnO4 nanoparticle layers at different temperatures ranging from 10 to 300 K. The InGaZnO4 nanoparticles prepared by metal–nitrate–glycol gel decomposition method exhibited ...
Added: June 6, 2026
Das A., Saikia J., Maji N. et al., ChemNanoMat 2026 Vol. 12 No. 5 Article e202500733
Developing efficient photoactive materials from bio-derived resources is vital yet challenging for achieving effective water splitting performance. In this work, nano carbon dots (CDs) of zero-dimensional (0D) were synthesized from papaya peel through a simple and eco-friendly process and subsequently anchored onto the two-dimensional (2D) layered structure of graphitic carbon nitride (g-C3N4, GCN) at various ...
Added: June 2, 2026
Wary R. R., Mahato B., Sharma N. et al., The Journal of Physical Chemistry Letters 2026 Vol. 17 No. 17 P. 5099–5107
Development of heterojunction materials is an efficient approach for enhancing photocatalytic and photoelectrochemical processes. We develop a ZnO/CuO heterojunction via Cu doping into a ZnO matrix. Structural characterization confirmed that Cu was effectively incorporated into ZnO without any structural changes. The improved optical properties and reduced charge carrier recombination of the doped samples were confirmed ...
Added: June 2, 2026
Duran E. ., Pulgar A., Izquierdo R. et al., Physica Status Solidi (A) Applications and Materials 2026 Vol. 223 No. 7 Article e202500942
Ceramic superconductors exhibit remarkable properties, including zero electrical resistance and potent magnetic behavior, operating at temperatures as high as the boiling points of liquid nitrogen (77 K) and liquid hydrogen (20 K). These characteristics position them as key enablers for sustainable technologies spanning electric propulsion, lossless energy transmission, advanced medical imaging, and quantum computation. This review presents ...
Added: June 1, 2026
Андреев Д. В., Корнев С. А., Bondarenko G. et al., Перспективные материалы 2026 № 6 С. 5–11
Выполнено сравнительное исследование процессов сильнополевой зарядовой
деградации подзатворного диэлектрика структур металл-диэлектрик-полупроводник (МДП)
с алюминиевым и поликремниевым затвором. Зарядовые явления в МДП-структурах
изучали методом сильнополевой инжекции электронов в диэлектрик в режиме возрастания
плотности стрессового инжекционного тока с кратковременными переключениями
в измерительный режим при постоянной низкой плотности инжекционного тока.
Использование данного метода позволило получить новые данные о процессах зарядовой
деградации подзатворного диэлектрика МДП-структур с ...
Added: May 21, 2026
Rathish S., Andrey S. Vasenko, Thazhathenair A. et al., The Journal of Physical Chemistry Letters 2026 Vol. 17 No. 18 P. 5386–5394
We demonstrate and rationalize the effect of Au nanoparticles (NPs) on the hierarchical g-C3N4/CeO2 heterojunction. g-C3N4/CeO2 decorated with monodispersed plasmonic Au NPs was synthesized. Detailed analyses showed that CeO2 nanocubes and monodispersed Au NPs were evenly distributed over the 2D g-C3N4 surface, forming a robust interface enriched with abundant active sites. The structure enabled efficient separation of photogenerated charge ...
Added: May 16, 2026
Paul R., Das A., Sharma N. et al., Colloids and Surfaces A: Physicochemical and Engineering Aspects 2026 Vol. 728 Article 138830
Niobium-doped TiO2 (Nb-TiO2), demonstrates dual functionality as an efficient photocatalyst for dye degradation and a promising photoelectrocatalyst for water oxidation. Nb incorporation via a facile hydrothermal method was confirmed by XRD (Rietveld refinement), XPS, TEM, FT-IR, Raman, and BET analyses, indicating successful lattice doping and structural modification. Photocatalytic dye degradation experiments were conducted using a model ...
Added: May 16, 2026
Гущина В. А., / Series chemrxiv-2023-vpzhz-v2 "ChemRxiv". 2023.
All-inorganic perovskite CsPbBr3 and Cs4PbBr6 nanoparticles are being intensively studied due to their unique properties and wide range of applications; however, however, the nature of their optical properties is not yet fully understood due to the difficulty of synthesis of singlephase nanoparticles. In this article we describe the features of the synthesis of single-phase particles ...
Added: May 14, 2026
Гущина В. А., Mendeleev Communications 2025 Vol. 35 No. 2 P. 193–195
All-inorganic perovskite CsPbBr3 and Cs4PbBr6 nanoparticles are intensively studied for their unique optical properties, though synthesizing single-phase nanoparticles has posed challenges. Detailed synthesis method of CsPbBr3 and Cs4PbBr6 single-phase nanoparticles and their chemical and phase analysis are described. Distinctive optical characteristics, such as photoluminescence, optical band gap and the Urbach tail region, are revealed and explained within the current ...
Added: May 14, 2026
Гущина В. А., Physics of Complex System 2026 Vol. 7 No. 1 P. 3–15
Heterostructures based on ZnO nanorods and CsPbBr3 nanocrystals were investigated for their potential as semiconductor SERS substrates. We found that ZnO morphology governs the efficiency of interfacial energy transfer, leading to enhanced photoluminescence under 390 nm excitation and a noticeable reduction of the bandgap in the composites. Raman analysis revealed a pronounced intensity enhancement and ...
Added: May 14, 2026
Гущина В. А., Russian Journal of Inorganic Chemistry 2024 Vol. 69 No. 6 P. 940–948
Currently, ABX3 nanoparticles (NPs) based on lead halides attract the attention due to their unique optical properties and a wide range of applications. The preparation of NPs with lead as a partial or complete replacement is particularly interesting because of the toxicity of this chemical element and most of its compounds. In this study, we propose a ...
Added: May 6, 2026
Morozov E. V., Demin A. S., Borovitskaya I. V. et al., Inorganic Materials: Applied Research 2026 Vol. 17 No. 3 P. 619–626
This article presents the results of experiments on the impact of powerful pulsed ion-plasma and
electron flows generated in the working chamber of the Plasma Focus PF-5M installation during each highvoltage
discharge on a model aluminum alloy B95. It is shown that the general characteristics of the alloy’s
damage upon exposure to pulsed flows of helium ions (HI) ...
Added: May 4, 2026
Pavlenko V. I., Bondarenko G.G., Cherkashina N. I. et al., Inorganic Materials: Applied Research 2026 Vol. 17 No. 2 P. 276–282
A composite material based on polyethylene, boron carbide (B4C), and bismuth oxide (Bi2O3) is
synthesized by the method of joint cryogenic milling of all components in liquid nitrogen environment followed
by pressing. The effect of cryogenic milling on the distribution of fillers in a composite is studied and
the prospects of using this method are assessed in comparison ...
Added: April 9, 2026
Черкашина Н. И., Павленко В. И., Bondarenko G. et al., Перспективные материалы 2026 № 4 С. 14–26
В данной работе представлен синтез гибкого полимерного композита для защиты от радиации на основе каучуковой матрицы и оксидов редкоземельных металлов, таких как Dy2O3 и Gd2O3, предназначенного для создания радиационно-защитных экранов и средств индивидуальной защиты. Исследованы его физико-механические характеристики: составы с добавлением оксида диспрозия имеют плотность от 1,31 до 2,44 г/см3, предел прочности при растяжении от ...
Added: April 2, 2026
Chowdhury U., Sarkar R., Sarkar P. et al., Nanoscale 2026 No. 15 P. 8115–8126
Added: April 1, 2026
IEEE, 2025.
THERMINIC is the major European Workshop related to thermal and reliability issues in electronic components and systems. For academics and industrialists involved in micro and power electronics this annual event promises to be a very special occasion with a high quality technical programme and exciting social events. ...
Added: November 5, 2025
Gabdukaev E., Naidenova I. N., Parshakov P., Общество и экономика 2025 № 10 С. 39–55
This study presents a systematic analysis of 7,566 articles from international peer-reviewed journals on transport infrastructure and economic development. Using machine-learning and cluster-analysis techniques, it identifies the field’s key research directions. The results reveal four dominant thematic clusters: sustainable transport, digitalisation, regional corridors and decarbonisation. Topic-trend analysis shows a rapid surge of interest in the ...
Added: October 10, 2025
Shelepenkov D., Essel A., Kosonogov V., American Journal of Physiology - Regulatory Integrative and Comparative Physiology 2025 Vol. 329 No. 1 P. R81–R85
Introduction. Skin temperature has been recognized as a potential marker of emotional arousal, with studies demonstrating temperature changes in response to various emotional stimuli. However, temperature in different body parts and in different basic emotions has not been studied sufficiently. Our study aimed to investigate whether basic emotions could be reflected in temperature changes at ...
Added: March 22, 2025
Dli M. I., Bobkov V. A., Bykov A. A. et al., CIS Iron and Steel Review 2024 Vol. 28 P. 4–8
The results of experimental analysis of the regularities of chemical and metallurgical process of iron-bearing ore desulfurization for different conditions of liquid phase sintering are presented. This process is conducted with addition of catalytic impurities and variation of chemical composition of the heat-carrying gas, in order to reveal the optimal procedure of chemical and metallurgical ...
Added: January 20, 2025