?
Оценка влияния неравномерности поверхности оптических кристаллических микрорезонаторов на их дисперсионные характеристики
Компьютерная оптика. 2023. Т. 47. № 4. С. 580–587.
Данилин А. Н., Yurin A., Кондратьев Н. М., Ружицкая Д. Д., Дмитриев Н. Ю., Булыгин Ф. В., Семенчинский С. Г., Krasivskaya M., Миньков К. Н.
Advantages and prospects of using optical microresonators for the development of measuring instruments based on frequency combs are described. A principle of a frequency comb generator based on an optical microresonator is considered. An example of modeling the properties of microresonators used to generate optical frequency combs is considered. The influence of the nonuniformity of the optical microresonator’s generatrix on the value of the total dispersion has been studied. It is shown that the presence of nonuniformity on the surface affects the dispersion parameters and can also lead to the effect of mode shape splitting in microresonators. We have shown that this effect is particularly dependent on the position and the value of the depth of nonuniformity.
IEEE, 2026.
The 9th International Scientific Conference on Information, Control, and Communication Technologies (ICCT-2025) had been held October 7-11, 2025 in Gomel, Belarus. The main technical areas and applications covered by the proceedings are optoelectronics, acousto-optic, microwave technology, antenna systems, measuring technology, metamaterials, nanostructures, nanofilms, photonic crystals, biology and medicine, biophotonics, bioengineering, neural networks in communication technologies; ...
Added: June 23, 2026
Plotnikov S., Альманах современной метрологии 2024 № 2(38) С. 140–149
The results of the analysis of data collected by the method of expert questioning of Russian scientific metrological institutes’ employees, as well as buyers of measuring instruments, are presented. ...
Added: May 21, 2026
Апрелев А. В., Пивоварова Н. И., Plotnikov S. et al., Альманах современной метрологии 2022 № 2(30) С. 94–101
The results of the analysis of data from the Federal Information Fund for Ensuring the Uniformity of Measurements in terms of oscilloscopes are presented. ...
Added: May 21, 2026
Stepanyants V., Хорошилов Г. С., Долгов И. М. et al., Труды Института системного программирования РАН 2026 Т. 38 № 3 С. 95–110
Highly automated and connected vehicles are gradually entering the market. Currently, solutions are being proposed that allow these technologies to be used for cooperative driving automation, which can significantly improve traffic safety. Such technologies and their software should be tested to ensure safety before being implemented in real systems. Verification and validation of vehicular control ...
Added: May 12, 2026
Левенков Я. Ю., Чичекин И. В., Вдовин Д. С. et al., Труды НАМИ 2025 № 1 (300) С. 17–30
Введение (постановка задачи и актуальность). В настоящее время широкое распространение получило использование автономных мобильных беспилотных транспортно-технологических средств (БТТС) при выполнении работ в зонах с вредными и опасными факторами. Также данные машины могут быть использованы для выполнения поисково-спасательных работ, доставки грузов в труднодоступные районы и иных подобных задач. Поэтому к таким БТТС предъявляются повышенные требования к ...
Added: April 16, 2026
Kuvshinov A., Fominykh A., Ivanov F., IEEE Access 2026 Vol. 14 P. 50549–50557
The recursive (U|U+V) construction, a generalization of which includes polar codes, provides a powerful framework for building complex codes from simpler components. However, existing approaches predominantly rely on fixed or symmetric tree architectures, overlooking the critical impact of decomposition choice on code performance. This paper addresses the challenge of optimal tree decomposition selection by presenting a framework ...
Added: April 7, 2026
Manohin A., Электрооборудование: эксплуатация и ремонт 2026 № 2 С. 75–85
An extended method for calculating heat transfer coefficients using programs
for automated analysis of the thermal regime of TRIANA (ASONIKA-T) radio-electronic
equipment for various designs is proposed. Based on the analysis of the obtained
heat transfer coefficients, it is shown how to set realistic values for the convective
heat transfer coefficient in SOLIDWORKS Simulation and other CAE thermal analysis
systems. ...
Added: April 3, 2026
SciTePress, 2024.
This book contains the proceedings of the 21st International Conference on Informatics in Control, Automation and Robotics. This year, ICINCO is held in Porto, Portugal, on November 18-20, 2024. It was sponsored by the Institute for Systems and Technologies of Information, Control and Communication (INSTICC), and technically co-sponsored by the IEEE Systems, Man and Cybernetics ...
Added: March 17, 2026
IEEE, 2025.
On behalf of the organizing committee, it is our great privilege to present this compendium of research
articles for the 11th International Conference on Automation, Robotics, and Applications (ICARA 2025),
which will be held in the vibrant city of Zagreb, Croatia from February 12 to 14, 2025. The proceedings
encapsulate the latest advancements and innovative research in the ...
Added: March 17, 2026
Cham: Springer, 2026.
This book delivers actionable insights through 21 peer-reviewed chapters featuring new methods, models, and applications based on computational intelligence. Discover cutting-edge tools to support smart, efficient decision-making in complex, real-world scenarios. Organized into three parts—prescriptive analytics, soft computing models, and practical case studies—it spans domains such as healthcare, energy, mobility, finance, and public services. Readers ...
Added: March 17, 2026
Frolov O. V., Safin R. N., Tsoy T. G. et al., Ученые записки Казанского университета. Серия: Физико-математические науки 2025 Vol. 167 No. 4 P. 786–805
Advancements in robotics have expanded a use of unmanned aerial vehicle (UAV) swarms in
critical tasks such as disaster response, including search and rescue operations during floods, hurricanes,
landsliding, and earthquakes. Swarm formation control stands as a critical challenge in UAV swarm
control. In this article, a simple and resource-efficient method for addressing collisions within swarm
formations during outdoor ...
Added: March 17, 2026
Springer, 2026.
The two volume set LNAI 16303 + 16304 constitutes the refereed proceedings of the 10th International Conference on Interactive Collaborative Robotics, ICR 2025, held in Hanoi, Vietnam, during November 10–13, 2025. The 58 full papers presented in these two volumes were carefully reviewed and selected from 143 submissions. The papers are organized in the following topical sections:
Part ...
Added: March 17, 2026
Springer, 2026.
This book includes selected papers from the Fifth International Conference on Agriculture Digitalization and Organic Production (ADOP 2025), held in Barnaul, Altai Region, Russia, during June 03-06, 2025. The topics covered in the book are ground robotic systems in crop production, unmanned aerial vehicles in crop production, aerospace monitoring tools in crop production, robotic animal ...
Added: March 17, 2026
Song J., Bai Y., Svinin M. et al., Artificial Life and Robotics 2026 P. 1–13
This study introduces an innovative control approach for deploying multiple unmanned aerial vehicles (UAVs) to monitor an unknown food region. The proposed strategy is designed to optimally distribute UAVs across the food-afected area while cooperatively estimating the extent of inundation. To achieve this, an adaptive coverage controller is developed based on Centroidal Voronoi Tessellation (CVT), incorporating a novel ...
Added: March 17, 2026
Kurtc V., Prokhorov A., Journal of Mathematical Sciences 2025 No. 295 P. 229–240
We present a methodology for calibrating doubly constrained gravity models. Three types of deterrence functions are examined: exponential, power, and combined. The latter includes two calibration parameters, whereas the others contain only one. The parameters are identified so that the model reproduces the observed trip length distribution with high accuracy. We test four optimization methods: ...
Added: March 12, 2026
Kiselev G., Prokhorov A., Journal of Mathematical Sciences. Vol. 295, No. 2, December, 2025. Mathematical Modeling and AI for Traffic Flows on Networks and Related Topics 2025 No. 295 P. 185–196
We study the problem of estimating the population and workplaces in a given area using open data sources and machine learning algorithms for automation and improvement of quality and accuracy of the transport demand calculation in transport modeling.
Bibliography: 6 titles. Illustrations: 7 figures. ...
Added: March 12, 2026
Mikolaenko V., Конюшенко М. Н., Стулков Л. Д., Механическое оборудование металлургических заводов 2025 № 2(25) С. 23–30
Uniaxial tensile testing of flat specimens under superplastic conditions is widely used to determine the deformation behavior of materials. However, the standard interpretation of the results relies on the hypothesis of an ideal uniaxial stress state and often fails to account for the influence of specimen geometry and material flow from the gripping zones to ...
Added: March 5, 2026
IEEE, 2026.
International Conference on Industrial Engineering, Applications and Manufacturing. ...
Added: February 25, 2026
Bosboom V., Van der Vegt J. J., Kupriyanov M. Y. et al., Superconductor Science and Technology 2022 Vol. 34 No. 11 Article 115022
We develop a quantitative model describing the distribution of the supercurrent density and
density of states in SN-N-NS type Josephson junctions in three dimensions (S is a
superconductor and N is a normal metal). The model is based on the self-consistent solution of
the quasiclassical Usadel equations using the finite element method. We investigate the
influence of the proximity ...
Added: October 31, 2022
Mikolaenko V., Journal of Physics: Conference Series 2021 Article 012022
Superplasticity is an ability of polycrystalline materials to archive extremely large deformations, which is utilized in advanced forming technologies demanded mainly in the aerospace industry. Design of such technologies needs an information of the material flow behaviour, which describes the relation of the effective stress on the strain and strain rate taking place during deformation. ...
Added: September 22, 2021
Zakhariev I., Journal of Physics: Conference Series 2021 Vol. 1740 P. 1–6
Superplastic blow forming is a technology of shell parts production. The development of these processes requires computer simulation which cannot be realized without accurate parameters of the applied material. This characterization can be based on results of free bulging tests. Characterization techniques utilize the models of the dome growth during the bulging test. This study ...
Added: January 27, 2021
Kazeev V., Oseledets I., Rakhuba M. et al., / Series math "arxiv.org". 2020.
Homogenization in terms of multiscale limits transforms a multiscale problem with n+1 asymptotically separated microscales posed on a physical domain D⊂ℝd into a one-scale problem posed on a product domain of dimension (n+1)d by introducing n so-called "fast variables". This procedure allows to convert n+1 scales in d physical dimensions into a single-scale structure in (n+1)d dimensions. We prove here that both the original, physical multiscale problem and the ...
Added: October 20, 2020
Borisov N., Kasatkin A., Presnyakov S., T-Comm: Телекоммуникации и транспорт 2019 Т. 13 № 2 С. 4–10
The task is to sharply reduce the complexity of analysis, multivariate analysis and parametric optimization of linear and linearized equivalent electrical circuits. The source of such schemes are not only linear electronic circuits, but also circuits formed on the basis of artificial electrical analogies. They can be formed on the basis of finite element methods ...
Added: March 1, 2019
Yakovlev E., Чекмарев Д. Т., Епифанов В. Ю., В кн.: Международная молодежная школа-семинар "Современная геометрия и ее приложения". Международная конференция "Современная геометрия и ее приложения". Материалы школы-семинара и конференции.: Каз.: Издательство Казанского университета, 2017. С. 164–168.
Finite element numerical schemes for solving the continuum mechanics problems are discussed. One of the authors developed a method of acceleration of calculations which uses the simplicial mesh inscribed in the original cubic cell partitioning of a three-dimensional body. In this work it is shown that the obstacle to the construction of this design may be ...
Added: December 6, 2018