?
Materials based on modified gypsum for facade systems
Нанотехнологии в строительстве: научный интернет-журнал. 2021. Vol. 13. No. 3. P. 144–149.
Zhukov A., Bessonov I. V., Bobrova E., Gorbunova E. A., Demissie B. A.
ABSTRACT: Introduction. The use of gypsum in construction systems exposed to atmospheric influences involves the introduction of modifying additives of various types: polymer compositions, mineral fine and nanodisperse components, which can also be products of other industries. Methods and materials. To increase the weather resistance of gypsum stone, its strength characteristics and water resistance, the research considered a complex method of modifying gypsum binder by introducing aqueous solutions of polycondensation resins that harden in the material and nanocomponents. The experiment to assess the effect of the composition of complexly modified gypsum on its properties was carried out on the basis of the matrix of a complete quadratic three-factor experiment. Results. The strength of a complex modified gypsum stone during compression and bending increases by 30% and 25%, respectively, during 80 days of storage in the air. The compressive strength is 60 MPa, and the bending strength is 12 MPa. The samples can withstand 150 cycles of alternating freezing and thawing. Discussion. The introduction of polymer additives into the composition of the gypsum mixture leads to the fact that the gypsum during hydration creates a framework of crystalline aggregates of dehydrate, and the resin, when cured, forms a continuous polymer matrix. The polymer gypsum has the property of increasing the strength over time due to the ongoing polymerization of the resin. Conclusion. A weather-resistant gypsum-containing material was obtained. The use of man-made waste makes it possible to solve the problem of their disposal, which determines the reduction of the negative load on the environment. The methodology for assessing the weather resistance of gypsum stone, and, first, frost resistance, was tested.
Language:
English
Das A., Saikia J., Maji N. et al., ChemNanoMat 2026 Vol. 12 No. 5 Article e202500733
Developing efficient photoactive materials from bio-derived resources is vital yet challenging for achieving effective water splitting performance. In this work, nano carbon dots (CDs) of zero-dimensional (0D) were synthesized from papaya peel through a simple and eco-friendly process and subsequently anchored onto the two-dimensional (2D) layered structure of graphitic carbon nitride (g-C3N4, GCN) at various ...
Added: June 2, 2026
Wary R. R., Mahato B., Sharma N. et al., The Journal of Physical Chemistry Letters 2026 Vol. 17 No. 17 P. 5099–5107
Development of heterojunction materials is an efficient approach for enhancing photocatalytic and photoelectrochemical processes. We develop a ZnO/CuO heterojunction via Cu doping into a ZnO matrix. Structural characterization confirmed that Cu was effectively incorporated into ZnO without any structural changes. The improved optical properties and reduced charge carrier recombination of the doped samples were confirmed ...
Added: June 2, 2026
Duran E. ., Pulgar A., Izquierdo R. et al., Physica Status Solidi (A) Applications and Materials 2026 Vol. 223 No. 7 Article e202500942
Ceramic superconductors exhibit remarkable properties, including zero electrical resistance and potent magnetic behavior, operating at temperatures as high as the boiling points of liquid nitrogen (77 K) and liquid hydrogen (20 K). These characteristics position them as key enablers for sustainable technologies spanning electric propulsion, lossless energy transmission, advanced medical imaging, and quantum computation. This review presents ...
Added: June 1, 2026
Arutyunov K., JIANG1 Q., FANG J. et al., Science China Information Sciences 2026 Vol. 69 No. 6 P. 1–11
Resonators based on nanoelectromechanical systems (NEMS) using two-dimensional (2D) materials with high-quality factors and excellent electrical control are critical for tunable coherent phonon dynamics, resonant sensors and wireless communications. However, their performance is fundamentally limited by the lack of a unified framework governing energy dissipation mechanisms and their electrical tunability. Here, we synergistically modulate both ...
Added: May 28, 2026
Elesin L., Shilov A., Jana S. et al., Advanced Functional Materials 2026 P. 1–10
Thermoelectric materials, long explored for energy harvesting and thermal sensing, convert heat directly into electrical signals. Extending their application to the terahertz (THz) frequency range opens opportunities for low-noise, bias-free THz detection, yet conventional thermoelectrics lack the sensitivity required for practical devices. Thermoelectric coefficients can be strongly enhanced near van Hove singularities (VHS), though these ...
Added: May 28, 2026
Андреев Д. В., Корнев С. А., Bondarenko G. et al., Перспективные материалы 2026 № 6 С. 5–11
Выполнено сравнительное исследование процессов сильнополевой зарядовой
деградации подзатворного диэлектрика структур металл-диэлектрик-полупроводник (МДП)
с алюминиевым и поликремниевым затвором. Зарядовые явления в МДП-структурах
изучали методом сильнополевой инжекции электронов в диэлектрик в режиме возрастания
плотности стрессового инжекционного тока с кратковременными переключениями
в измерительный режим при постоянной низкой плотности инжекционного тока.
Использование данного метода позволило получить новые данные о процессах зарядовой
деградации подзатворного диэлектрика МДП-структур с ...
Added: May 21, 2026
Kaveev A. K., Fedorov V. V., Pavlov A. V. et al., Journal of Materials Chemistry C 2026 Vol. 14 No. 7 P. 2697–2705
Bismuth nanostructures represent a promising material platform for semiconductor nanooptoelectronics and colorimetry owing to the multi-colored light reflection and quantum confinement. In this work, we study the photoluminescent properties of bismuth nanostructures grown using molecular beam epitaxy on the planar CaF2/Si(111) surface. We demonstrate the different surface morphologies of Bi, ranging from planar films obtained ...
Added: May 19, 2026
Масютин Д. А., Moiseev E., Komarov S. et al., Письма в Журнал технической физики 2026 Т. 52 № 7 С. 27–30
Исследованы инжекционные полупроводниковые микролазеры с кольцевым резонатором радиусом 15 мкм с несимметричным расположением внутреннего отверстия резонатора. Показано, что асимметрия обеспечивает формирование в диаграмме направленности двух лепестков излучения, разориентированных на 50° относительно оси смещения внутреннего отверстия. Измеренная добротность резонаторов сопоставима с добротностью дисковых резонаторов и находится на уровне ∼ 10^6. ...
Added: May 18, 2026
Rathish S., Andrey S. Vasenko, Thazhathenair A. et al., The Journal of Physical Chemistry Letters 2026 Vol. 17 No. 18 P. 5386–5394
We demonstrate and rationalize the effect of Au nanoparticles (NPs) on the hierarchical g-C3N4/CeO2 heterojunction. g-C3N4/CeO2 decorated with monodispersed plasmonic Au NPs was synthesized. Detailed analyses showed that CeO2 nanocubes and monodispersed Au NPs were evenly distributed over the 2D g-C3N4 surface, forming a robust interface enriched with abundant active sites. The structure enabled efficient separation of photogenerated charge ...
Added: May 16, 2026
Paul R., Das A., Sharma N. et al., Colloids and Surfaces A: Physicochemical and Engineering Aspects 2026 Vol. 728 Article 138830
Niobium-doped TiO2 (Nb-TiO2), demonstrates dual functionality as an efficient photocatalyst for dye degradation and a promising photoelectrocatalyst for water oxidation. Nb incorporation via a facile hydrothermal method was confirmed by XRD (Rietveld refinement), XPS, TEM, FT-IR, Raman, and BET analyses, indicating successful lattice doping and structural modification. Photocatalytic dye degradation experiments were conducted using a model ...
Added: May 16, 2026
Гущина В. А., / Series chemrxiv-2023-vpzhz-v2 "ChemRxiv". 2023.
All-inorganic perovskite CsPbBr3 and Cs4PbBr6 nanoparticles are being intensively studied due to their unique properties and wide range of applications; however, however, the nature of their optical properties is not yet fully understood due to the difficulty of synthesis of singlephase nanoparticles. In this article we describe the features of the synthesis of single-phase particles ...
Added: May 14, 2026
Гущина В. А., Mendeleev Communications 2025 Vol. 35 No. 2 P. 193–195
All-inorganic perovskite CsPbBr3 and Cs4PbBr6 nanoparticles are intensively studied for their unique optical properties, though synthesizing single-phase nanoparticles has posed challenges. Detailed synthesis method of CsPbBr3 and Cs4PbBr6 single-phase nanoparticles and their chemical and phase analysis are described. Distinctive optical characteristics, such as photoluminescence, optical band gap and the Urbach tail region, are revealed and explained within the current ...
Added: May 14, 2026
Гущина В. А., Physics of Complex System 2026 Vol. 7 No. 1 P. 3–15
Heterostructures based on ZnO nanorods and CsPbBr3 nanocrystals were investigated for their potential as semiconductor SERS substrates. We found that ZnO morphology governs the efficiency of interfacial energy transfer, leading to enhanced photoluminescence under 390 nm excitation and a noticeable reduction of the bandgap in the composites. Raman analysis revealed a pronounced intensity enhancement and ...
Added: May 14, 2026
Легонькова О. А., Стаффорд В. В., Винокурова Т. И. et al., Физикохимия поверхности и защита материалов 2025 Т. 61 № 2 С. 196–206
Проведены обобщающие сравнительные исследования по изменению поверхностных, физико-механических свойств биорезорбируемых нитей in vitro и in vivo, реакции тканей на использование шовных материалов с разными сроками биодеструкции: сополимер лактида с гликолидом (ПГЛ), полидоксанон (ПДО), сополимер гликолида и ε-капролактона (ПГК). Определена причина возникновения возможной воспалительной реакции тканей. Процесс биодеструкции для всех нитей начинается с поверхности, сопровождается “выщелачиванием” ...
Added: February 19, 2026
Paukov M. I., Starchenko V. V., Melnikov A. et al., Materials Today Chemistry 2024 No. 36 Article 101886
Added: July 24, 2025
An P. P., V. V. Kovalyuk, Y. G. Gladush et al., Applied Physics Letters 2024 Vol. 125 No. 20 Article 201101
The rapid development of photonic integrated circuits (PICs) and their applications in various fields of science and technology requires the creation of easy-to-manufacture high-speed integrated detectors. In this work, we fabricated and studied planar waveguide-integrated bolometers based on a thin film of single-walled carbon nanotubes (SWCNTs) on the silicon nitride platform. This bolometer showed good ...
Added: November 11, 2024
E. Yu. Bobrova, Popov I. I., A. D. Zhukov et al., Russian Journal of Building Construction and Architecture 2022 No. 4(56) P. 29–38
The resistance of foamed polymers to various types of loads is determined by the density of the material, its structure and the rigidity of the polymer matrix, as well as the nature of the porosity of the material. Foamed polymers with a polymodal cellular porosity structure show their resistance to a greater extent under various ...
Added: March 19, 2023
Mukhangali S., Neplokh V., Kochetkov F. et al., Applied Physics Letters 2022 No. 121 Article 243504
This paper demonstrates an elastic (i.e., both flexible and stretchable) pixel matrix based on the patterned films of single-walled carbon nanotubes, which were obtained using optical lithography and plasma etching. The proposed elastic electrodes maintain their initial resistivity at 10% stretching. We also demonstrate an application of the elastic pixel matrix to an array of ...
Added: December 14, 2022
Bondarenko G., М.: ООО "Лаборатория знаний", 2016.
Учебное пособие посвящено описанию физических основ взаимодействия высокоэнергетических излучений с веществом, сущности и закономерностям радиационно-индуцированных процессов, протекающих в облученных твердых телах, таких как образование первичных структурных дефектов и их эволюция, фокусировка атомных столкновений и каналирование частиц, структурно-фазовые превращения в сплавах, трансмутационные эффекты, электризация диэлектриков, распухание, радиационное охрупчивание и ползучесть, ионное распыление, радиационный блистеринг и др. ...
Added: December 8, 2016
Novikov L., Voronina E. N., Chirskaya N. P., Inorganic Materials: Applied Research 2014 Vol. 4 No. 2 P. 107–115
Features of formation and migration of radiation-induced defects in carbon nanotubes (CNT) and nanostructured materials are examined. The main methods and software tools used for the simulating nanomaterial structure and space factors are described. The results of mathematical simulation are presented. ...
Added: March 2, 2015
Voronina E. N., Lev S. Novikov, RSC advances 2013 Vol. 3 No. 35 P. 15362–15367
We apply first principles calculations to compare the carbon and boron nitride nanotube unzipping under atomic oxygen impact. We show that the attack of several oxygen atoms can cause bond breaking in nanotubes, but the structure of boron nitride nanotubes is less damaged than the structure of carbon ones. With increasing diameter, the structural damage ...
Added: March 2, 2015
Nikolaev D. P., Физика волновых процессов и радиотехнические системы 2014 Т. 17 С. 13–18
Main conception of fullerenes that represents a molecular formula of carbon and about single-layer and multilayer carbon nanotubes. Structure of nanotubes are presented in this article. Main methods of multilayer nanotube production are brought into account. Carbon nanotubes are usually produced in a process of condensation of carbon-metallic vapor by catalytic pyrolysis of hydrocarbon formula ...
Added: December 8, 2014
Fedorov G., Kardakova A., Gayduchenko I. et al., Applied Physics Letters 2013 Vol. 103 P. 181121-1–181121-5
We report on the voltage response of carbon nanotube devices to sub-terahertz (THz) radiation. The devices contain carbon nanotubes (CNTs), which are over their length partially suspended and partially Van der Waals bonded to a SiO2 substrate, causing a difference in thermal contact. We observe a DC voltage upon exposure to 140GHz radiation. Based on ...
Added: March 13, 2014
Vasin V. A., Vasichev B. N., Stepanchikov S. V. et al., МГОУ-XXI - Новые технологии 2012 № 3 С. 17–24
Рассмотрены вопросы построения микро- и нано- устройств с применением нанотехнологий. Представлены модели наносборки и роста нанообъектов, свойства нанообъектов и наноустройств. Описаны технологические и метрологические проблемы создания и внедрения нанопродуктов, микросистемной техники и микромеханики. ...
Added: February 2, 2014