?
Influence of ground effect on longitudinal aerodynamic damping of wing-in-ground effect vehicles
Ship Technology Research. 2020. Vol. 67. No. 2. P. 101–108.
Accurate determination of longitudinal stability characteristics of wing-in-ground (WIG) effect vehicles is an essential step in their design. In order to estimate WIG vehicle’s stability, one needs to determine aerodynamic derivatives, including unsteady ones. The latter are very hard to obtain via wind tunnel tests, so traditionally they are expressed via steady derivatives. The method presented in this paper allows calculating unsteady aerodynamic derivatives by means of Reynolds-averaged Navier–Stokes simulations. The effect of different aerodynamic derivatives on stability characteristics is investigated. It is demonstrated that the decrement is two times greater in case of taking into account the unsteady aerodynamic derivatives calculated according to the presented method.
Research target:
Mechanics and Mechanical Engineering
Language:
English
Viacheslav K., Русский инженер 2024 № 3 С. 34–37
Analysis of various methods referred to the increasing energy efficiency and movement safety through the use of
control systems which take into account the force factors of interaction of the wheel propeller with the supporting surface. During
the analysis of methods dedicated to energy efficiency rise and were used techniques of logical and statistical analysis. There are
various ...
Added: May 19, 2026
Interpretable Machine Learning in Guided Synthesis of Stable Sols Based on Nanosized Titanium Oxides
Glushko A., Neznanov A., Kuz'micheva G. et al., , in: 2026 International Conference on Artificial Intelligence, Computer, Data Sciences and Applications (ACDSA), 5-7 Feb. 2026.: IEEE, 2026. P. 1–6.
This report discusses the guided synthesis of sols containing nanosized titanium(IV) oxides for use in biological and medical applications. These sols vary in size (from ∼2 up to 2000nm) and different stability (from 0 up to 90 days). They are synthesized under changing fabrication conditions (temperature, hydrolysis duration, titanium-containing precursors composition and concentration) without surfactants. ...
Added: April 29, 2026
Левенков Я. Ю., Чичекин И. В., Вдовин Д. С. et al., Труды НАМИ 2025 № 1 (300) С. 17–30
Введение (постановка задачи и актуальность). В настоящее время широкое распространение получило использование автономных мобильных беспилотных транспортно-технологических средств (БТТС) при выполнении работ в зонах с вредными и опасными факторами. Также данные машины могут быть использованы для выполнения поисково-спасательных работ, доставки грузов в труднодоступные районы и иных подобных задач. Поэтому к таким БТТС предъявляются повышенные требования к ...
Added: April 16, 2026
Карцев А. И., Physics of Metals and Metallography 2025 Vol. 125 No. 14 P. 1935–1939
The problem of the maximum oscillation frequency of composite bimetallic microactuators excited by thermal pulses has been theoretically investigated. Both traditional bimetallic composites made of metals and alloys with different coefficients of thermal expansion and composites in which one of the layers is made of a mechanically pre-stressed shape memory alloy (SMA) and the other ...
Added: March 16, 2026
Mikolaenko V., Конюшенко М. Н., Стулков Л. Д., Механическое оборудование металлургических заводов 2025 № 2(25) С. 23–30
Uniaxial tensile testing of flat specimens under superplastic conditions is widely used to determine the deformation behavior of materials. However, the standard interpretation of the results relies on the hypothesis of an ideal uniaxial stress state and often fails to account for the influence of specimen geometry and material flow from the gripping zones to ...
Added: March 5, 2026
Maltseva S. V., Голубцов П. В., Барахнин В. Б., Вычислительные технологии 2026 Т. 31 № 1 С. 5–22
The issues of macro-level monitoring of the manufacturing system in the implementation of the concepts of Industry 4.0 and 5.0 based on the study of information flows in manufacturing network structures are considered. The numerical models of three types of network interaction, that taking into account the influence of the number of objects, external influences, ...
Added: February 26, 2026
Yasnitsky L., Голдобин М. А., Мезенцев А. С., Прикладная математика и вопросы управления 2025 № 2 С. 99–116
Представлен обзор современных методов и основанных на них программных
инструментах, применяемых для математического моделирования серийных производственных процессов с целью снижения брака и повышения качества производимых изделий. Перечисляются группы работ, нацеленных на обнаружение и классификацию дефектов, работ, в которых решаются задачи прогнозирования образования дефектов и определения значимости параметров, работ направленных на поиск
оптимального сочетания технологических параметров изготовления изделий, ...
Added: February 15, 2026
Мартынова И. А., Дакашева Т. М., В кн.: XLVIII Самарская областная студенческая научная конференция: тезисы докладовТ. 2.: Эко-Вектор, 2022. С. 176–177.
В процессе научно-технического прогресса, а также в связи с последними событиями на мировом пространстве, связанными с пандемией короновируса и другими непредвиденными изменениями, все интенсивнее возрастает потребность специалистов дать названия новым реалиям в своих исследованиях. ...
Added: February 4, 2026
Мартынова И. А., , in: The European Proceedings of Social and Behavioural Sciences: Global Challenges and Prospects of the Modern Economic DevelopmentVol. 106.: European Publisher, 2021. P. 2357–1330.
In the new challenging time, corporate social responsibility has become a central issue for universities to get through the crisis caused by COVID-19. Under the crisis success of universities is directly dependent on their students’ level of satisfaction. The higher their rate of satisfaction is the greater are the chances to succeed. Thus, one of ...
Added: February 4, 2026
Арженовский И. В., Региональная экономика и управление: электронный научный журнал 2021 № 3 (67) Статья 11
At the present stage, regional specializations are being formed in the framework of the next technological wave, which is characterized by digitalization, “green” economy, bio- and nanotechnology, knowledge-based economy, and growing attention to human capital. The changes resulting from the Covid-19 pandemic belong to these characteristics as well. The article analyzes the influence of these ...
Added: January 21, 2026
Baimova J., Bessonov N., Krivtsov A. et al., Physical Review E - Statistical, Nonlinear, and Soft Matter Physics 2024 Vol. 110 No. 6 Article 065004
We present analytical and numerical investigations of the size and shape evolution of localized disturbances during their propagation in elastic media (furthermore, we refer to this process as energy dispersion). We consider two models of media: the continuum, described by the multidimensional wave equation, and the simple scalar harmonic lattice. The presented research is based ...
Added: November 12, 2025
Dmitriy Demin, Ilya Grebenkin, Alexey Barinov, International Journal of Advanced Manufacturing Technology 2025 Vol. 141 P. 1847–1858
In this paper, a computer simulation of round wire drawing processes with different equations of state for steel A12 has been carried out. In addition, the methods of improving the configuration of neural networks based on a multilayer perceptron (MLP) for estimating the distributions of residual stress tensor components have been investigated. The study demonstrated ...
Added: November 6, 2025
Zharkevich O., Berg A., Reshetnikova O. et al., Fluids 2025 Vol. 10 No. 8 Article 211
This article presents a comprehensive experimental and theoretical study and substantiation of the hydraulic parameters of a prototype multi-gear pump. The proposed pump design, which features one drive gear and four driven gears, aims to address the common disadvantages of traditional gear pumps, including radial force imbalance, uneven flow, high acoustic noise, and increased fluid ...
Added: November 6, 2025
Afanasiev V., Куприянов А. О., Неусыпин К. А., Авиакосмическое приборостроение 2025 № 9 С. 37–45
The problem of a zero-sum differential stabilization game with a quadratic performance functional is considered. The navigation system of an aircraft, including a platform inertial navigation system with structural correction using a control algorithm, is investigated. Errors of the navigation system, subject to the influence of uncontrolled disturbances, are described by a nonlinear ordinary differential ...
Added: November 1, 2025
R V., P H., Seralan V. et al., Fractal and Fractional 2022 Vol. 6 No. 10 Article 591
This study presents an extended dissipative analysis of fractional order fuzzy networked control system with uncertain parameters. First, we designed the network-based fuzzy controller for the considered model. Second, a novel Lyapunov-Krasovskii functional (LKF) approach, inequality techniques, and some sufficient conditions are established, which make the proposed system quadratically stable under the extended dissipative criteria. ...
Added: October 15, 2025
Konstantin Polyakov, Marina Polyakova, Polyakov A., Procedia Computer Science 2025 Vol. 266 P. 205–212
This study is devoted to the analysis of the relationship between the solution of two different tasks facing the management of a commercial organization - ensuring the efficiency and sustainability of the business. An analysis of publications on this topic shows the existence of contradictory conclusions. The authors hypothesize that there is a strong statistical ...
Added: October 8, 2025
Sorbale A., Stremoukhov D., Shevtsova I., Политическая наука 2025 № 3 С. 36–62
External shocks have a significant impact on the quality of governance and the stability of political systems around the world. The concept of resilience, which until recently was only actively used in natural science research, has become a key focus for political scientists studying the impact of crises on political institutions in various country contexts. ...
Added: September 4, 2025
Semakov S., Semakov I., IEEE Transactions on Aerospace and Electronic Systems 2022 Vol. 58 No. 6 P. 5425–5442
We propose the method for calculating the probability of a safe landing for ship-based aircraft. We define a safe landing as the event that the initial touch of the landing surface by an aircraft occurs on a given segment of the deck, and at the time of this contact, the phase coordinates of the aircraft ...
Added: August 9, 2025
Семаков С. Л., Семакова М. В., Автоматика и телемеханика 2023 № 3 С. 126–138
This paper considers aircraft landing on a carrier. We propose two schemes for calculating, first, the probability of a go-around due to disengaging the arresting gear and, second, the maximum descent of the aircraft’s trajectory with respect to the deck level immediately after leaving the deck. The instant to increase the aircraft’s thrust before touching ...
Added: August 8, 2025
Семаков С. Л., М.: Наука, 2005.
В могографии излагается взгляд на теорию случайных процессов как инструмент математического моделирования. В первой главе рассматриваются основные классы и характеристики случайных процессов; вторая посвящена выбросам случайных процессов: задачам о пересечениях и касаниях фиксированного уровня, экстремумах, первом достижении границ заданной области; третья - приложениям математических результатов в авиации. Ядром второй и третьей глав работы являются результаты ...
Added: August 5, 2025
Sergei L. Semakov, Cambridge Scholars Publishing, 2019.
The behavior of any real system is a process to a greater or lesser degree probabilistic. As a rule, it is impossible to specify exactly which external influences and internal mechanisms of interaction of the system components will be decisive in the future. As a consequence, we cannot accurately predict the behavior of the system. ...
Added: August 3, 2025
Yasnitsky L., Голдобин М. А., Прикладная информатика 2025 Т. 20 № 3(117) С. 85–100
Currently, artificial intelligence methods are widely used in the practice of serial production enterprises. They are used to detect defects, classify and eliminate them, identify the causes of defects, predict the quality and properties of the resulting product, select optimal parameters of the production process, and identify and study its patterns. However, outside the field ...
Added: July 10, 2025
Yasnitsky L., Мартыненко С. В., Поленова М. С. et al., Литейное производство 2025 № 7 С. 35–41
An artificial intelligence system (AIS) has been created based on a neural network trained on data from the production process of steel castings weighing up to 500 kg obtained by the open-hearth method. The AIS has 20 input parameters characterizing the chemical composition of the metal, melting parameters, out-of-furnace steel treatment modes, season, meteorological conditions, ...
Added: July 10, 2025
Плотников М. Ю., Ушанов С. А., Куничкин Д. П. et al., Оптический журнал 2025 Т. 92 № 8 С. 51–61
Subject of study. The paper presents the results of experimental investigation of the method of suppression of fading noise of a coherent optical reflectometer based on synchronous frequency-hopping of the optical source. Aim of study. The main goal of the work was to improve the accuracy of measurements of a coherent optical reflectometer using the ...
Added: June 23, 2025