?
МОДЕЛИРОВАНИЕ ПРОЦЕССА СВОБОДНОЙ ГАЗОВОЙ ФОРМОВКИ ЛИСТОВОЙ ЗАГОТОВКИ
С. 20-21.
Language:
Russian
Publication based on the results of:
In book
М. : МИЭМ НИУ ВШЭ, 2015
Zakhariev I., Aksenov S. A., Journal of Chemical Technology and Metallurgy 2017 Vol. 52 No. 5 P. 1002-1007
Free bulging process is an experimental technique which can be used to characterize a sheet material in conditions of biaxial tension during hot forming. Analytical and semi-analytical models of this process are usually based on the hypothesis offering certain relations between the geometrical characteristics of a bulge during forming. The paper presents an original relation ...
Added: December 11, 2016
Zakhariev I., Journal of Physics: Conference Series 2021 Vol. 1740 P. 1-6
Superplastic blow forming is a technology of shell parts production. The development of these processes requires computer simulation which cannot be realized without accurate parameters of the applied material. This characterization can be based on results of free bulging tests. Characterization techniques utilize the models of the dome growth during the bulging test. This study ...
Added: January 27, 2021
Aksenov S. A., Chumachenko E. N., Osipov S. et al., Procedia Engineering 2014 Vol. 81 P. 1017-1022
This study proposes a method for determining the material constitutive equations and optimal forming conditions on the basis of free bulging tests. The blow-forming tests were carried out at the temperature of 420 °C using aluminum alloy (AMg-6) sheets of a 1 mm thickness. Each test was performed at constant pressure. For each fixed value ...
Added: October 16, 2014
Zakhariev I., В кн. : Авиакосмические технологии (АКТ-2015):Тезисы I тура XVI Всероссийской научно-технической конференции и школы молодых ученых, аспирантов и студентов. : Воронеж : ООО Фирма "Элист", 2015. С. 105-107.
The work is devoted to the definition OT4-1 alloy properties on the multidome forming experiments. For verification of obtained results computer simulation was performed. ...
Added: October 20, 2015
Zakhariev I., В кн. : 12-я Международная конференция «Авиация и космонавтика – 2013». Тезисы докладов. : СПб. : Мастерская печати, 2013. С. 192-194.
В работе получено первое приближение механических свойств сплава АМг6 на основе результатов испытаний по свободной формовки куполов с постоянным давлением. Проведенный анализ позволил построить предварительную модель механических свойств сплава АМг6. ...
Added: December 24, 2013
Mikolaenko V., В кн. : Материалы конференции. Межвузовская научно-техническая конференция студентов, аспирантов и молодых специалистов им. Е.В. Арменского. : М. : МИЭМ НИУ ВШЭ, 2020. С. 16-18.
Работа посвящена компьютерному моделированию пластического формоизменения материала в условиях, близких к плоско-деформированному состоянию. Для моделирования такой задачи предлагается использовать метод конечных элементов с геометрическими ограничениями на элементы, что позволит учесть уширение образца, не прибегая к увеличению числа элементов при переходе от плоского моделирования к трехмерному. В рамках данной работы такой подход реализован в программных компонентах, ...
Added: January 31, 2023
Kishchik M. S., Mikhailovskaya A. V., Levchenko V. S. et al., Metal Science and Heat Treatment 2017 Vol. 58 No. 9 P. 543-547
A proсеss for fabriсating 5.mm-thiсk shеets from alloy l565сh with rеcrystallized grains lеss than l0 µm in sizе is dеvеlopеd, whiсh involvеs supеrplastiс forming and providеs еlеvatеd mесhaniсal propеrtiеs at room tеmpеratuге.Тhе paramеtеrs of supеrplastiсitу and thе mесhaniсal propеrtiеs of alloy l565сh arе dеtегminеd. Tеst forming оf a domе-shapе modеl part is pеrformеd. ...
Added: October 19, 2016
Puzino Y. A., , in : Innovative Information Technologies: Materials of the International scientific–practical conference. Part 2. * 2.: M. : HSE, 2014. P. 432-437.
This aim of this paper is the interpretation of the results of mechanical testing of materials to determine their properties under hot deformation. As an example, a simulation of rod stretching in superplasticity mode was considered. Comparing obtained data with the analytical solution was conducted. ...
Added: May 26, 2014
Chumachenko E. N., Смирнов О. М., Цепин М. А., М. : Либроком, 2009
В монографии анализируются особенности технологических процессов деформирования материалов в условиях сверхпластичности и проблемы, возникающие при работе с материалами, обладающими повышенной скоростной чувствительностью. Приведена математическая постановка задачи о медленном течении физически нелинейных сред с учетом контактного трения, обсуждаются ограничения на применение модели и некоторые частные решения. Особое внимание уделено моделированию контактного взаимодействия в процессах обработки металлов ...
Added: January 17, 2014
Aksenov S. A., Chumachenko E. N., Logashina I. V., Materials Science Forum 2013 Vol. 762 P. 392-397
This paper presents the research of the flow characteristics of the Ti-6V-4Al alloy in wide ranges of temperature (725 ‑ 950 °C) and strain rate (10-5 ‑ 10-2 s-1). The material processing maps were constructed based on the basis of dynamic materials model (DMM) developed by Prassad and modified by Narayana Murty. For the construction of such maps the data of ...
Added: July 3, 2013
Puzino Y. A., Aksenov S. A., В кн. : 12-я Международная конференция «Авиация и космонавтика – 2013». Тезисы докладов. : СПб. : Мастерская печати, 2013. С. 241-243.
Computer simulation of mechanical testing is used primarily for the correct interpretation of their results and is particularly relevant in cases, when the properties of the material during deformation are essentially nonlinear. For example: when we study mechanical properties of materials with high rate sensitivity. First of all it is superplastic titanium alloys. Superplastic materials ...
Added: November 15, 2013
Chumachenko E. N., Aksenov S. A., Logashina I. V., , in : METAL 2012. 21st International Conference on Metallurgy and Materials, Conference proceedings. : Ostrava : TANGER, 2012. P. 295-302.
Работа посвящена проектированию и оптимизации технологий сверхпластической формовки (СПФ). Условия сверхпластичности очень чувствительны к скорости деформации и температуре, характерной для процесса деформации. Представленная работа предлагает подход к проектированию технологий СПФ, позволяющих реализовывать данное состояние материала. Рассмотрены возможности уменьшения температуры промышленной формировки сплава ВТ-6 (Ti-6Al-4V). На основе полученных экспериментальных данных построены трехмерная компьютерная аппроксимация механических характеристик ...
Added: March 8, 2013
Puzino Y. A., Aksenov S. A., В кн. : Материалы VIII Всероссийской конференции по механике деформируемого твердого тела (Чебоксары, 16-21 июня 2014 г.): в 2 ч. Ч. 2.: Чебоксары : ФГБОУ ВПО "Чувашский государственный педагогический университет им. И.Я. Яковлева", 2014. С. 138-140.
A series of calculations of the stretching process with axisymmetric samples with different height in superplastic conditions using imitation simulation was held. As material was chosen Ti-Al6-V4 alloy. Dependencies of the obtained stresses and forces in central areas of samples from the size of the cylinders were obtained. ...
Added: January 19, 2015
Mikolaenko V., В кн. : Межвузовская научно-техническая конференция студентов, аспирантов и молодых специалистов имени Е.В. Арменского. Материалы конференции. : М. : МИЭМ НИУ ВШЭ, 2021. С. 39-42.
Применение эффекта сверхпластичности при реализации процессов обработки материалов давлением позволяет осуществлять бездефектное формоизменение листовых заготовок для получения оболочечных деталей сложной геометрической формы. Данный эффект возникает в специальных и промышленных сплавах на основе титана и алюминия. При разработке новых сплавов, обладающих эффектом сверхпластичности, особое внимание уделяется их деформационному поведению при повышенных температурах. Модель, описывающая деформационное поведение ...
Added: January 31, 2023
Mikolaenko V., В кн. : Межвузовская научно-техническая конференция студентов, аспирантов и молодых специалистов имени Е.В. Арменского. Материалы конференции. : М. : МИЭМ НИУ ВШЭ, 2022. С. 34-37.
Формовка листовых заготовок из сверхпластиче-ского материала - это технологический процесс, позволяющий получать тонкостенные изделия сложной геометрической формы. При реализации такого процесса необходимо задавать режим давления и температуры исходя из модели деформационного поведения материала. Существует множество экспериментальных методик, позволяющих получить такую модель, среди которых основной является механическое испытание плоских образцов на одноосное растяжение с постоянной скоростью ...
Added: January 31, 2023
Aksenov S. A., Chumachenko E. N., Logashina I. V., , in : METAL 2012. 21st International Conference on Metallurgy and Materials, Conference proceedings. : Ostrava : TANGER, 2012. P. 1239-1245.
The purpose of this study is to find out the characteristics of hot forming of Ti-6Al-4V titanium alloy in order to determine the conditions of its superplastic behavior. The experiments were performed in two stages: the stepped tensile-tests series (temperature range 700 – 925 °С) and the constant strain rate tensile-test series (temperature range 775 ...
Added: January 23, 2013
Aksenov S. A., Chumachenko E. N., Logashina I. V., , in : XIII International Scientific Conference "New technology and achievements in metallurgy and material engineering". * 1. Issue 24.: Częstochowa : Wydawnictwo Wydzialu Inzynierii Procesowej, Materialowej i Fizyki Stosowanej Politechniki Czenstochowskiej, 2012. P. 281-285.
The purpose of this study is to find out the characteristics of hot forming of Ti-6Al-4V titanium alloy in order to determine the conditions of its superplastic behavior. Based on experiments conducted in uniaxial tension of flat samples, the stress-strain curves were obtained and examined in a wide range of temperatures and strain-rates. On the ...
Added: January 23, 2013
Chumachenko E. N., Портной В. К., Logashina I. V., Металлург 2014 № 12 С. 68-71
The various test methods for determining the mechanical properties of materials in a state of superplasticity were considered. The tension depends from the deformation and strain rate, the structural parameter and temperature. The rheology and mechanics of superplastic deformation were discusses. Methodology has been tested and gave good results when tested Ti alloys and constructing ...
Added: February 9, 2015
Kotov A. D., Mikhaylovskaya A. V., Kishchik M. S. et al., Journal of Alloys and Compounds 2016 Vol. 688 P. 336-344
Highlights
•
Superplastic behaviour and the microstructural evolution were investigated.
•
Alloy with Al3(Sc,Zr) particles and alloy containing Al3Zr and Al3Ni particles.
•
Alloy with Ni and Zr exhibits a 1.5–2 times finer grains during deformation.
•
Al3Ni particles provide a larger number of nuclei for recrystallization.
Abstract
The superplastic properties of two high strength aluminium alloys are investigated. The first alloy contains fine, coherent ...
Added: September 9, 2016
Chumachenko E. N., Портной В. К., Logashina I. V., Металлург 2015 № 1 С. 76-81
The various test methods for determining the mechanical properties of materials in a state of superplasticity were considered. The tension depends from the deformation and strain rate, the structural parameter and temperature. The rheology and mechanics of superplastic deformation were discusses. Methodology has been tested and gave good results when tested Ti alloys and constructing ...
Added: February 9, 2015
Zakhariev I., Aksenov S. A., В кн. : Тезисы докладов V Международного научного семинара «Динамическое деформирование и контактное взаимодействие тонкостенных конструкций при воздействии полей различной физической природы». : М. : МЦВДНТ «Москва», 2016. С. 77-78.
Работа посвящена проблеме определения реологических характеристик материалов по результатам тестовых формовок листовой заготовки в цилиндрическую матрицу. Интерпретация результатов тестов осуществлялась посредством обратного анализа. Полученные характеристики материала верифицировались c помощью конечно-элементного моделирования. Результаты моделирования продемонстрировали хорошую согласованность с экспериментальными данным. ...
Added: December 11, 2016
Mikhaylovskaya A. V., Mosleh A. O., Kotov A. et al., Materials Science & Engineering A: Structural Materials: Properties, Microstructure and Processing 2017 No. 708 P. 469-477
Superplastic deformation behaviour of conventional sheets of a near-α titanium alloy (Ti-2.5Al-1.8Mn) was studied by a step-by-step decrease of the strain rate and constant strain rate tests in a temperature range of 790–915 °C. The research found that superplastic deformation is possible in a temperature range of 815–890 °С and a constant strain rate range ...
Added: December 1, 2017
Mosleh A., Mikhaylovskaya A., Kotov A. et al., Metals 2017 Vol. 7 No. 12 P. 1-15
The paper focuses on developing constitutive models for superplastic deformation behaviour of near-αtitanium alloy (Ti-2.5Al-1.8Mn) at elevated temperatures in a range from 840 to 890 °C and in a strain rate range from 2 × 10−4 to 8 × 10−4 s−1. Stress–strain experimental tensile tests data were used to develop the mathematical models. Both, hyperbolic sine Arrhenius-type ...
Added: February 1, 2018
Zakhariev I., Aksenov S. A., Logashina I. V., Металлург 2016
The paper is oriented toward the problem of superplastic materials characterization using free bulging testing. This experimental technique allows one to study the material flow behavior in conditions of biaxial tension which is very close to the ones occurring during hot gas forming. The interpretation of the results is proposed to perform by inverse analysis ...
Added: June 19, 2016