?
Investigation of the welded layer hardness at restoration of electric motor shafts
Journal of Applied Engineering Science/Istrazivanja i Projektovanja za Privredu. 2025. Vol. 23. No. 2. P. 322–329.
The article is devoted to studying the influence of wire feed rate on the hardness of the welded layer during the restoration of electric motor shafts. The authors analyse the importance of optimal hardness to ensure the durability and reliability of the reconditioned parts. The paper considers various factors affecting the hardness of the welded layer, such as type of welding wire (AWS A5.18 ER70S-6, OK Tubrodur 35 G M, AWS A5.28 ER80S-G); cladding modes (feed rate, current, voltage); properties of the welded clad metal (fusion with the base, tendency to crack formation). Based on the conducted experiments, the optimal welding modes for each of the studied wires and the corresponding hardness values were determined. The obtained results allow us to conclude that the wire feed rate is one of the key parameters affecting the hardness of the welded layer.
Merzlinkin V., Khmelev A. V., Севрюков Д. О. et al., St. Petersburg Polytechnical University Journal: Physics and Mathematics 2025 No. 3 P. 205–209
Laser communication using satellites represents a promising avenue for data transmission in geographically distant areas without advanced infrastructure. This approach is characterized by its high transmission rate and low power requirements, providing substantial benefits over optical fiber and radio communication. However, the optical channel should exhibit greater transparency for light transmission, resulting in a severely restricted application of this technique for information ...
Added: October 5, 2026
Дуплинский А. В., Khmelev A. V., Бахшалиев Р. М. et al., St. Petersburg Polytechnical University Journal: Physics and Mathematics 2026 Vol. 17 No. 3 P. 88–92
Quantum key distribution via satellites enables the technology to be applied attranscontinental scale; nevertheless, in contrast to fiber systems, using a free-space opticalcommunication channel presents certain extra technological obstacles. The contribution of theacquisition, pointing and tracking system’s operation to the potential quantum bit error valueis investigated in this research. The polarization extinction ratio measurements varying ...
Added: October 5, 2026
Miller A., Pismeniuk L., Дуплинский А. В. et al., EPJ QUANTUM TECHNOLOGY 2023 Vol. 10 No. 1 P. 52–72
A satellite-constellation based global quantum network could allow secure quantum
communication between remote users worldwide. Such a constellation could be
formed of micro- or even nanosatellites, which have the advantage of being more
cost-effective than larger expensive spacecrafts. At the same time, the features of
quantum communication impose a number of technical requirements that are more
difficult to meet when ...
Added: October 5, 2026
Le M. T., Шукуров И. С., Курск: Закрытое акционерное общество "Университетская книга", 2026.
This monograph studies the thermal characteristics of urban habitats and analyzes the impact of urban morphology on the emergence of urban heat island effects (UHI), particularly in the context of high-density urban development, modern high-rise buildings and related sanitary standards. It presents comprehensive findings from theoretical and empirical research focused on minimizing the urban heat ...
Added: September 30, 2026
Starodubov K., Елистратов А. А., Громов Ю. Ю. et al., ИД Академии Жуковского, 2026.
The textbook is intended for preparing and completing practical assignments on biometric identification and the protection of biometric data. The theoretical part briefly presents the information required for the practical work: basic concepts and quality metrics, voice and facial modalities, regulatory framework and the Unified Biometric System, the mathematical foundations of template protection, and the ...
Added: September 19, 2026
Кузнецов М. Е., Полякова М., Лукьянович В. et al., ФАНУ "Востокгосплан", 2026.
Обзор международных практик развития робототехники и искусственного интеллекта и оценка возможностей их применения в условиях России, в первую очередь для Дальнего Востока и Арктической зоны РФ ...
Added: September 16, 2026
Starodubov K., Кривоногов А. А., Плоткин А. С. et al., Нано-био-технологии. Тепло- и электроэнергетика. Математическое моделирование: сборник статей III международной научно-практической конференции (Липецкий государственный технический университет, Липецк, Россия) 2025 С. 300–309
The paper considers the problem of assessing the criticality of defects in smart contracts, defines the constituent parameters of criticality of defects and substantiates their representation in the form of LR-type fuzzy numbers. An approach based on the use of LR-type fuzzy numbers and nonlinear optimization methods is proposed to assess the criticality of defects ...
Added: September 7, 2026
Starodubov K., Гвасалия Г. В., Карасев П. И., Нано-био-технологии. Тепло- и электроэнергетика. Математическое моделирование: сборник статей III международной научно-практической конференции (Липецкий государственный технический университет, Липецк, Россия) 2025 С. 219–223
This paper discusses the concept of neural networks, convolutional neural networks, their architecture and their operation principle. The main attention is paid to testing the reliability of storing images of people as embeddings, which are considered to be unrecoverable in the original image. In the course of the research an experiment is carried out: the ...
Added: September 6, 2026
Шейкин В. В., Starodubov K., Карасев П. И., XXI век: итоги прошлого и проблемы настоящего плюс 2026 Т. 15 № 2(74) С. 20–25
The paper addresses the problem of formalized description of intruder behavior in government information systems. An approach based on hidden Markov models is proposed for modeling the actions of an intruder, where the stages of malicious activity are interpreted as hidden states and the events registered by the system are treated as observable symbols of ...
Added: September 6, 2026
Максимова Е. А., Утешева Г. Ш., Громов Ю. Ю. et al., Научно-аналитический журнал "Вестник Санкт-Петербургского университета Государственной противопожарной службы МЧС России" 2026 № 2 С. 92–103
When data are incomplete, standard fuzzy data mining methods face an unacceptable trade-off: deleting objects with missing values loses up to a third of the sample and introduces systematic bias under the MAR mechanism, while mean imputation destroys the covariance structure and produces rules with artificially inflated support. This paper proposes a different solution - ...
Added: September 6, 2026
Bubnova M., Chetverikov V., Pozhidaev E., Информационные технологии 2026 Т. 32 № 8 С. 404–413
A specialized methodology was developed, computer modeling was conducted, and a comparative analysis was performed for autonomous control methods for small spacecraft, differing in how the nonlinearity of the initial stabilization problem is taken into account:
— control constructed using a system of linear differential equations (SLDE);
— control constructed using SLDE applied to a more general ...
Added: September 2, 2026
Шейкин В. В., Starodubov K., Безопасность. Управление. Искусственный интеллект 2026 Т. 3 № S3 С. 47–57
The article proposes a formal apparatus for risk analysis in information systems based on the apparatus of fuzzy logic, graph theory and matrices. A system of definitions is introduced that includes a universe of entities, sets of violators and destructive influences, as well as membership functions describing the fuzzy relationships between them. A risk calculation ...
Added: August 29, 2026
Воронеж: Издательский дом ВГУ, 2026.
В сборник вошли материалы XXXII Международной научно-технической конференции «Радиолокация, навигация, связь» (RLNC*2026), прошедшие ре цензирование членами программного комитета конференции. Основной целью конференции является организация взаимодействия научных и научно технических коллективов для обмена опытом и новыми творческими успехами. Достижение этой цели также способствует внедрению перспективных разрабо ток, имеющих практическое значение для дальнейшего развития промышленно сти, экономики ...
Added: August 29, 2026
Romanov A., Физулин А. В., Stepanyants V., Московский транспорт. Наука и проектирование 2026 № 2 С. 77–90
The behaviour of connected automated vehicles in implementing cooperative safety functions
depends on the timely exchange of V2X messages. At the same time, the end-to-end impact of 5G NR-V2X
Mode 2 message delivery failures on vehicle behaviour requires evaluation not only by aggregated network
metrics but also by the timeliness of V2X message arrival within the time window ...
Added: August 25, 2026
Белгородский государственный технологический университет им. В.Г. Шухова, 2026.
В сборнике опубликованы доклады студентов, аспирантов и молодых ученых, представленные по результатам проведения Международной научно-технической конференции молодых ученых БГТУ им. В.Г. Шухова. Материалы статей могут быть использованы студентами, магистрантами, аспирантами и молодыми учеными, занимающимися вопросами энергоснабжения и управления в производстве строительных материалов, архитектурных конструкций, электротехники, экономики и менеджмента, гуманитарных и социальных исследований, а также в ...
Added: August 19, 2026
Междуреченск: Кузбасский государственный технический университет им. Т.Ф. Горбачева, 2026.
В сборнике представлены материалы докладов по направлениям Международной научно-практической конференции «Современные тенденции и инновации в науке и производстве»: 1. Технологии и инновации в горной промышленности; 2. Экономика, управление, финансы; 3. Информационные системы и технологии; 4. Юный исследователь. Целью этой конференции является обмен передовым опытом, повышения квалификации их участников и, вместе с тем, это способ установления и укрепления научного сотрудничества среди ...
Added: August 11, 2026
Scientific publishing house Infinity, 2026.
These Conference Proceedings combine materials of the conference –
research papers and thesis reports of scientifi c workers. They examine technical,
juridical and sociological aspects of research issues. Some articles deal
with theoretical and methodological approaches and principles of research
questions of personality professionalization. ...
Added: July 24, 2026
IEEE, 2025.
The 9th International Scientific Conference on Information, Control, and Communication Technologies (ICCT-2025) had been held October 7-11, 2025 in Gomel, Belarus. The main technical areas and applications covered by the proceedings are optoelectronics, acousto-optic, microwave technology, antenna systems, measuring technology, metamaterials, nanostructures, nanofilms, photonic crystals, biology and medicine, biophotonics, bioengineering, neural networks in communication technologies; ...
Added: June 23, 2026
Anandkumar M., Kesavan K. P., Sudarsan S. et al., Nanomaterials 2025 Vol. 15 No. 12 Article 939
High-entropy ceramics have gained wider attention due to their structural integrity and stability, which can be used in various functional applications. Especially, high-entropy oxides exhibit excellent thermal stability, particularly at high temperatures. Thermal barrier coating materials must demonstrate good thermal stability without any phase transformation or phase separation, which is critical in aerospace and energy ...
Added: June 30, 2025
Alizadeh M., Karimi A., Pashangeh S. et al., Journal of Materials Research and Technology 2025 Vol. 35 P. 4647–4659
In this research, the structural features, tribological performance, and corrosion resistance of an Al/Cu/MoS2/WC hybrid composite fabricated by the accumulative roll bonding (ARB) method were analyzed. Microstructural observations indicated that a uniform dispersion of Cu, MoS2, and WC particles is achieved after seven ARB passes. No phase transition occurred during ARB process. Moreover, hardness tests ...
Added: June 11, 2025
Vasiliev S. V., Limanovskii A. I., Tkachenko V. M. et al., Materials Science & Engineering A, Нидерланды 2022 Vol. 850 Article 143420
The fully consolidated bilayer (consisting of two amorphous Al86Ni9Gd5 melt-spun ribbons) disks with a diameter
of 5 mm were produced using unconstrained high pressure torsion (HPT) processing subjecting for 2–5 turns at
applied pressures of 2 and 4 GPa. The structure and mechanical properties of the disks as well as those of the asprepared
and heated up to ...
Added: October 19, 2022
Skazochkin A. V., Bondarenko G.G., Zukowski P., Приборы и методы измерений 2020 Vol. 11 No. 3 P. 212–221
The aim of the article was to study the hardness of a metal surface modified with ultrafine particles of minerals by two different methods (instrumental indentation and Vickers hardness measurement) and a comparative analysis of the measurement results obtained by these methods.Standard Vickers hardness measurements at loads of 0.025, 0.1, and 0.5 kgf showed a ...
Added: September 23, 2020
Bliznets Ivan, Cygan M., Komosa P. et al., , in: Approximation, Randomization, and Combinatorial Optimization. Algorithms and Techniques (APPROX/RANDOM 2016)Vol. 60.: Schloss Dagstuhl--Leibniz-Zentrum fuer Informatik, 2016. Ch. 3 P. 1–17.
The H-free Edge Deletion problem asks, for a given graph G and integer k, whether it is possible to delete at most k edges from G to make it H-free, that is, not containing H as an induced subgraph. The H-free Edge Completion problem is defined similarly, but we add edges instead of deleting them. ...
Added: October 31, 2018
Pogrebnjak A. D., Beresnev V. M., Smyrnova K. V. et al., Materials Letters 2018 Vol. 211 P. 316–318
The multicomponent nitride coatings from TiZrNbAlYCr high entropy alloy (HEA) were fabricated using the vacuum-arc method. The effect of nitrogen pressure on the crystallite size, elemental and phase composition of (TiZrNbAlYCr) N coatings was investigated. A bias voltage applied to the substrate during the deposition process was -200 V. The partial nitrogen pressure was 0.05 ...
Added: January 15, 2018