?
О возможностях новой технологии минеральных покрытий для повышения износостойкости металлической поверхности при создании деталей вакуумной техники
С. 78-82.
Skazochkin A. V., Bondarenko G.G., Żukowski P., Devices and Methods of Measurements (Belarus) 2019 Vol. 10 No. 3 P. 263-270
A comparative study of the wear resistance, hardness and modulus of elasticity of ENAW-2024 aluminum alloy samples with and without a mineral coating was carried out. The wear resistance of the samples was studied by the method of multi-cycle friction, which makes it possible to measure the physicomechanical properties of thin modified material layers at ...
Added: September 12, 2019
Skazochkin A. V., Bondarenko G.G., Kislov S. V., Journal of Engineering Science and Technology Review 2018 Vol. 11 No. 6 P. 138-143
The work investigates some tribological parameters of the surfaces of friction pairs made of steel, with mineral layers. A comparative study of the friction coefficient of 18CrNiMo7-6 steel specimens with and without a mineral coating is
performed. The lowest friction coefficient value was achieved for samples with mineral coating, without HFC hard
surfacing before creating a mineral ...
Added: March 6, 2019
Кислов С. В., Кислов В. Г., Балаш П. В. et al., Нефтегазовое дело 2015 № 4 С. 231-254
Новая технология создания минеральных покрытий на металлической поверхности была использована для создания износостойких слоев на резьбовых соединениях стальных насосно-компрессорных труб. Выполнены сравнительные исследования и определен ресурс работы резьбового соединения стальных насосно-компрессорных труб в исходном состоянии и после нанесеения минерального слоя. По результатам испытаний сделан вывод о том, что упрочняющее минеральное покрытие увеличивает износостойкость резьбового соединения ...
Added: September 11, 2015
Skazochkin A. V., Bondarenko G.G., Zukowski P., Приборы и методы измерений 2020 Vol. 11 No. 3 P. 212-221
The aim of the article was to study the hardness of a metal surface modified with ultrafine particles of minerals by two different methods (instrumental indentation and Vickers hardness measurement) and a comparative analysis of the measurement results obtained by these methods.Standard Vickers hardness measurements at loads of 0.025, 0.1, and 0.5 kgf showed a ...
Added: September 23, 2020
Bondarenko G., Kislov S., Skazochkin A. et al., , in : Proceedings of 9th international conference "New electrical and electronic technologies and their industrial implementation". : lublin University of Technology, 2015. P. 99-99.
In the report the results of investigations of structural changes on a surface and in near-surface layers of samples from steel 20Cr13 (Rus.) and a titanic alloy of PT-3V (Rus) after each stage of creation of the strengthening mineral blanket on the offered technology have been presented. Use of an electrospark alloying, application of pressure ...
Added: July 15, 2015
Vasin V. A., Ivashov E., Кузнецов П. С. et al., Электромагнитные волны и электронные системы 2011 № 4 С. 49-55
Рассмотрены особенности проектирования элементов и устройств вакуумного оборудования, предназначенных для реализации экологически чистых и энергосберегающих технологий в электронном производстве. Выполнены расчёты коэффициентов трения материалов, работающих в вакууме, в зависимости от разрежения окружающей среды, для различных случаев контактного взаимодействия, а так же – интенсивности изнашивания пар трения в зависимости от нагрузки, микрогеометрии контакта, скорости скольжения, остаточного ...
Added: April 12, 2012
Kislov S. V., Kislov V. G., Skazochkin A. V. et al., Russian Metallurgy (Metally) 2015 No. 7 P. 558-564
The structural changes that occur in the surface and surface layers of steel 20Kh13 and titanium alloy PT3V (Russian designation) samples after each stage of hardening due to a formed mineral surface layer are studied by optical microscopy, transmission electron microscopy, and scanning electron microscopy. Electric spark alloying, pressing, and ultrasonic processing are used to ...
Added: October 22, 2015
Kislov S. V., Kislov V. G., Balasch P. V. et al., IOP Conference Series: Materials Science and Engineering (MSE) 2016 Vol. 110 No. 012096 P. 1-5
The article describes the advantages of the new technology of mineral coating of metal products for the friction pair of mechanical systems. It presents the research results of the wear rate of the samples made of 12X13 steel (X12Cr13) with mineral layers, in the experiments with a piston ring sliding inside a cylinder liner with ...
Added: February 24, 2016
Vasin V. A., Ivashov E., Кузнецов П. С. et al., Структурная Надёжность 2011 № 2 С. 40-48
Представлены методы расчёта трибоэкологических параметров, влияющих на загрязнение внутрикамерных объёмов вакуумного оборудования и дефектность, привносимую на обрабатываемые изделия электронной техники. Выполнен расчёт коэффициентов трения материалов, работающих в вакууме в зависимости от разряжения окружающей среды для случаев упругого и пластичного контактного взаимодействия, а также расчёт интенсивности изнашивания пар трения в зависимости от нагрузки, микрогеометрии контакта, скорости ...
Added: December 14, 2012