?
Нанесение покрытий в трубках на установке Плазменный фокус
С. 308–311.
Колокольцев В. Н., Боровицкая И. В., Парамонова В. В., Ляховицкий М. М., Гайдар А. И., Eriskin A. A., Bondarenko G., Силин П. В., Никулин В. Я.
The paper explored the possibility of obtaining coatings in the interior cavity of thin Cu tubes on the plasma focus devices. A special feature of such devices is the generation of thin plasma jets of high power. It has been shown the fundamental possibility of receiving protective coating in tubes (Cu) due to the erosion of the anode material (Cu, W). Coating was carried out under the influence of the impulse (t<0,1 µs) argon and deuterium plasma. Coating is a composite material with complex composition, containing the chemical elements, such as Cu, O2, C, W, Fe, Ni. It has been achieved a high value of strength for the coating obtained by processing of the inner cavity Cu tube by Ar plasma in a magnetic field B≤0,1 T.
Keywords: плазменный фокуснанесение покрытийhigh-temperature pulsed plasmaplasma focusвысокотемпературная импульсная плазмазащитные покрытияcoatingsмикротвердостьdeuterium plasmaдейтериевая плазмаargon plasmaаргоновая плазмаcoating in tubescoating in narrow gapscoating in thin holesprotective Coatingsmicrohardnessпокрытия в трубкахнанесение покрытий в узких щеляхнанесение покрытий в тонких отверстиях
In book
Мн.: Издательский центр БГУ, 2015.
Ostovari Moghaddam A., Shaburova N. A., Mikhailov D. et al., Journal of Chemical Technology and Metallurgy 2025 Vol. 60 No. 4 P. 645–652
AlCoCrFeNi2.1 eutectic high entropy alloy (HEA)composite coatings reinforced by Al2O3 particles were prepared by detonation spraying (DS) on low alloy steel substrates. The effect of annealing at different temperatures on the microstructure and mechanical properties of the coatings was further studied. The as-deposited AlCoCrFeNi2.1 - 30 wt. % Al2O3 composite coating exhibited a dual-phase FCC+BCC ...
Added: August 29, 2025
Shaburova N., Pashkeev I., Samoilova O. et al., COATINGS 2022 Vol. 13 No. 1 Article 70
Saturation diffusion with chromium has not been adequately studied among all the surface thermochemical treatment (STCT) processes of steels. Especially, the complex saturation behavior when several elements are added directly for chemical treatment needs to be systematically studied. This work aims at determining the effect of V, Mo, and Co on the parameters of chromium ...
Added: February 18, 2025
Lashkari A. H., Ostovari Moghaddam A., Naseri M. et al., Journal of Materials Research and Technology 2023 Vol. 24 P. 5024–5031
In the present work, the formation of high entropy MAX phase during mechanical alloying and subsequent spark plasma sintering (SPS) of two powder mixtures with (HfZrNbTiTa)3SiC2 and (HfZrNbTiTa)3(SiAl)1.1C1.95 stoichiometries is investigated. The results indicate that a high entropy carbide (HEC) with cubic HfC-prototype structure is formed for both compositions after 7 h of mechanical alloying. The ...
Added: February 18, 2025
Samoilova O., Shaburova N., Samodurova M. et al., Journal of Thermal Spray Technology 2023 Vol. 32 No. 5 P. 1220–1229
In this work, the morphology, microstructure, and phase composition of Al0.25CoCrFeNiSi0.6 high-entropy alloy coating (HEAC) deposited on stainless steel by detonation spraying (DS) are investigated. The Al0.25CoCrFeNiSi0.6 HEA ingot was first prepared by induction melting and then crushed and ground to ≤ 100 µm using a planetary ball milling apparatus. Detonation spraying was carried out on a computerized ...
Added: February 18, 2025
Ostovari Moghaddam A., Shaburova N., Naseri M. et al., Metals 2023 Vol. 13 No. 11 Article 1807
Ni-based composite coatings reinforced by high-entropy intermetallic compounds (HEICs) were prepared by detonation spraying (DS) on low alloy steel substrates. To this end, first (Ti-Nb)(V-Cr-Ni-Fe) and Al3(TiZrNbCrHfTa) HEIC powders were fabricated by arc melting followed by ball milling. The as-milled HEIC powders were then employed as reinforcement particles to prepare Ni-7wt.% HEIC composite coatings. The ...
Added: February 18, 2025
Ostovari Moghaddam A., Mikhailov D., Shaburova N. et al., Colloids and Surfaces A: Physicochemical and Engineering Aspects 2025 Vol. 710 Article 136291
In this work, (Fe20Co23.9Ni20Cr15)(Al20Ti1.1) and [(Fe20Co23.9Ni20Cr15)(Al20Ti1.1)]98.5B1.5 chemically complex intermetallic alloys (CCIMAs) were first prepared by vacuum melting followed by ball milling, and then employed as precursor powders for depositing coatings on a low alloy steel substrate using detonation spraying. The precursor CCIMAs exhibited a dense lamellar dual-phase microstructure consisting of multicomponent L12 and Cr-rich BCC ...
Added: February 8, 2025
Ostovari Moghaddam A., Shaburova N., Pashkeev K. et al., Transactions of the Indian Institute of Metals 2025 Vol. 78 Article 61
In this study, BaFe12O19 and three corresponding BaFe6(AlCrTiGaCo)6O19, BaFe2(AlCrTiGaCo)10O19 and BaFe6(AlCrSnGaCo)6O19 high-entropy oxides (HEOs) particles were utilized as reinforcement particles to fabricate Al-matrix composites coatings using cold gas dynamic spraying technique. First, BaFe12O19 and HEOs reinforcement particles with a single BaFe12O19-type structure were fabricated by solid-phase sintering and ball milling. Then, Al-matrix composites with a ...
Added: February 8, 2025
Ahmad Ostovari Moghaddam, Sudarikov M., Shaburova N. et al., Metals 2024 Vol. 14 No. 1 Article 50
This study aims at investigating the feasibility of depositing quality coatings from various high-entropy intermetallic compounds (HEICs) using detonation spraying (DS). Four different HEIC coatings, namely (NbTaVCrTi)Al3, (NbTaVNiFe)Al3, (NbTaVZrHf)Al3, and (FeNiCoCrMn)(MoCr), were prepared by DS on low alloy steel substrates. The HEIC powders were first prepared by arc melting followed by ball milling and then ...
Added: January 23, 2025
Polyakova M., Ahmad Ostovari Moghaddam, Trofimova S. et al., Engineering Research Express 2024 Vol. 6 No. 4 Article 042402
There is a continuous demand to design materials with comprehensive properties as the boundaries of human works extend to new branches of technological activities. For designing parts from new materials, it is essential to consider the possible technological problems and economic aspects, however, not always the solution is evident. In this regard, multi-component high entropy ...
Added: January 12, 2025
Ahmad Ostovari Moghaddam, Shaburova N., Zhivulin D. et al., Journal of Alloys and Compounds 2025 Vol. 1010 Article 177238
Cold gas dynamic spraying was attempted as a new technique to additively fabricate functionally graded Cu-matrix composites reinforced by BaFe12O19 and its corresponding BaFe6(AlCrTiGaCo)6O19, BaFe2(AlCrTiGaCo)10O19 and BaFe6(AlCrSnGaCo)6O19 high entropy oxides (HEOs) particles. The BaFe12O19 and HEOs reinforcement particles, prepared by solid-phase sintering and ball milling, exhibited a single BaFe12O19-type structure and homogenous microstructure. Cu-matrix composites with a gradient lamellar ...
Added: December 29, 2024
Боровицкая И. В., Демин А. С., Комолова О. А. et al., Металлы (Российская Академия наук, Российская Федерация 2023 № 4 С. 34–42
Представлены результаты исследования воздействий импульсных потоков ионов гелия (ИГ) и гелиевой плазмы (ГП) на сплав Инконель 718, приготовленный по аддитивной технологии методом селективного лазерного сплавления с последующей термической обработкой. Определены основные структурные изменения в облученном поверхностном слое (ПС) для двух режимов облучения – мягкого (с плотностью мощности излучения q = 2 ∙108 Вт/см2 при длительности ...
Added: July 3, 2023
Гнесин И. Б., Металловедение и термическая обработка металлов 2020 № 6 С. 39–43
The characteristics of heat resistance and microstructure of an advanced multilayer protective coating on carbon-carbon composite materials are investigated. The thermomechanical compatibility of the coating with the base material, its thermal stability, resistance to thermal shocks and cracking were evaluated. ...
Added: October 29, 2022
Borovitskaya I. V., Pimenov V. N., Maslyaev S. A. et al., Russian Metallurgy (Metally) 2022 No. 1 P. 48–56
The changes in the mechanical properties and the texture of the surface layers in Cu–10Ga and Cu–10Ga–4Ni alloys are studied under the powerful pulsed radiation-thermal and shock-wave loads characteristic of pulsed thermonuclear fusion plants. Samples are irradiated by pulsed high-temperature plasma and ions in the 600-kJ Plasma Focus (PF) PF-1000 (Poland) plant, and deuterium is ...
Added: April 16, 2022