?
Экспериментальное исследование формы тока ЭСР при разряде с печатной платой
Технологии электромагнитной совместимости. 2014. № 1(48). С. 46-52.
Charged board model (CBM) is considered. CBM is specific case of charged device model ESD event. The case of lowering components CDM rating, reported by other researchers, is considered. ESD current waveform experimaetal measurements and simulations were performed. Experimental and simulation results are in good match.
Research target:
Electronics and Electrical Engineering
Priority areas:
engineering science
Language:
Russian
Kuznetsov V., Kechiev L., IEEE Transactions on Electromagnetic Compatibility 2015 Vol. 57 No. 5 P. 947-954
In this paper, power MOS transistor behavior under charged board model (CBM) ESD impact is considered. The analysis of the MOSFET failure condition at the CBM ESD event is performed. The CBM equivalent circuit is proposed. The physical parameters of the PCB and device under test are replaced by the lumped RCL circuit. The MOSFET ...
Added: January 1, 2016
Kechiev L., Kuznetzov V. V., Abrameshin A. E., Технологии электромагнитной совместимости 2014 № 1(48) С. 46-52
Charged board model (CBM) is considered. CBM is specific case of charged device model ESD event. The case of lowering components CDM rating, reported by other researchers, is considered. ESD current waveform experimaetal measurements and simulations were performed. Experimental and simulation results are in good match ...
Added: April 28, 2014
Kechiev L., Kuznetzov V. V., Технологии электромагнитной совместимости 2013 № 1(44) С. 29-38
Проведено моделирование воздействия электростатического разряда на МОП-транзисторы, установленные на печатной плате. Результаты моделирования сравниваются с результатами испытаний тестовой печатной платы на воздействия ЭСР и проводится исследование воздействия печатной платы на порог отказа МОП-транзисторов при воздействии ЭСР по сравнению с их собственным порогом отказа. Обнаружено снижение порога отказа при ЭСР для транзисторов, установленных на печатной плате. ...
Added: May 3, 2013
Yelizarov (Elizarov) A. A., Zakirova E., Изобретения. Полезные модели. Официальный бюллетень Федеральной службы по интеллектуальной собственности, патентам и товарным знакам 2013 № 16
Изобретение относится к микрополосковой технике и может быть использовано для создания высокоэффективных СВЧ устройств и антенн. Сущность изобретения заключается в том, что печатная плата содержит планарные импедансные проводники, расположенные на диэлектрической подложке с изотропным металлическим экраном. Согласно предложенному изобретению диэлектрическая подложка выполняется многослойной, с числом слоев не менее трех, толщиной каждого слоя равной четверти рабочей ...
Added: November 7, 2013
Kusnetsov V. V., Kechiev L. N., , in : Innovative Information Technologies: Materials of the International scientific–practical conference. Part 2. * 2.: M. : HSE, 2014. P. 545-548.
Discusses modeling of semiconductor components on printed circuit boards by electrostatic discharges. ...
Added: April 28, 2014
Shalumov A. S., Урюпин И. С., Тихомиров М. В. et al., Динамика сложных систем 2012 Т. 6 № 3 С. 100-105
Исследованы программные продукты, предназначенные для расчета надежности несущих конструкций радиоэлектронной аппаратуры. Представлен алгоритм работы модуля расчета надежности несущих конструкций, включаемого в систему АСОНИКА. ...
Added: November 26, 2012
Агапов В. В., Технологии электромагнитной совместимости 2009 № 2 С. 72-75
Electrostatic Discharges, Interferences, Cables, Spacecraft, Onboard Electronics. This paper presents an original test equipment of the electrostatic discharge interferences in a spacecraft cables. Received current transformation into disturb voltage coefficients in the cable sections are used in calculation of interference levels at inputs of a spacecraft onboard radio-electronic equipment. ...
Added: April 10, 2013
Novikov L., Хасаншин Р. Х., Гаценко Л. С. et al., Перспективные материалы 2015 № 1 С. 22-29
A comparative analysis of electrostatic discharges on surfaces of К-208 and CMG glasses under irradiation by 10- to 40-keV electrons with flux densities from 1010 to 2,5×1011 cm-2s-1 in vacuum was done. The discharges accompanied by plasma ejections into surrounding and formation of microprotrusions and discharge channels were observed on the both glasses. However, the ...
Added: August 30, 2015
D. A. Abrameshin,, E. D. Pozhidaev,, V. S. Saenko et al., IEEE Transactions on Plasma Science 2019 Vol. 47 No. 8 P. 3653-3657
Abstract—We have performed computer simulations and experimental studies of characteristics of a standard analog device—the heterodyne employing a printed circuit board (PCB) made from a composite dielectric with a controlled dark conductivity. Simulation results show that an increased conductivity of the PCB smaller than 2 × 10^−7 Ohm^−1 · m^−1 has almost no effect on the ...
Added: May 27, 2019
Kechiev L., Kuznetzov V. V., IEEE Transactions on Electromagnetic Compatibility 2015 Vol. 57 No. 5 P. 947-954
In this paper, power MOS transistor behavior under charged board model (CBM) ESD impact is considered. The analysis of the MOSFET failure condition at the CBM ESD event is performed. The CBM equivalent circuit is proposed. The physical parameters of the PCB and device under test are replaced by the lumped RCL circuit. The MOSFET ...
Added: January 15, 2016
Kechiev L., Технологии электромагнитной совместимости 2009 № 4(31) С. 69-83
Рассматриваются основные принципы минимизации помех в шинах питания печатных плат цифровых устройств. Поясняются физические процессы образования и подавления помех, даются рекомендации по выбору и установке развязывающих конденсаторов, а также по рациональному конструированию печатных плат и расположению на них этих конденсаторов. ...
Added: January 6, 2013
Zhadnov V. V., Технологии электромагнитной совместимости 2015 № 4 С. 29-34
Indicators of maintainability of modern electronic devices greatly depend on the characteristics of reliability of electronic components. The impact of catastrophic electrical overstress due to electrostatic discharge can lead to failures of integrated circuits, which are widely used in electronic tools. The article considers the issues of assessing the impact of electrostatic discharges on the ...
Added: October 26, 2015
Abrameshin A. E., Zhadnov V. V., Технологии электромагнитной совместимости 2014 № 2 С. 27-34
Indicators of non-failure operation of the onboard space equipment substantially depend on characteristics of reliability microcircuits. One of possible causes of failures microcircuits is influence of catastrophic electrical overstress owing to electrostatic discharges. In article the method of formation of mathematical model of failure rate microcircuits and possibility of its application for microcircuits for the ...
Added: June 10, 2014
Shalumov A. S., Урюпин И. С., Динамика сложных систем 2012 Т. 6 № 2 С. 92-100
In article techniques of modeling of radio-electronic equipment in subsystems of ASONIKA-M and АSONIKА-М-IGS are considered, and also the method of increase of reliability of bearing constructions of radio-electronic equipment is described. Examples are resulted. ...
Added: November 26, 2012
Zhadnov V. V., Мир измерений 2016 № 4 С. 8-11
В статье рассматриваются вопросы оценки надёжности электронных измерительных приборов при проектировании. Приводится описание моделей интенсивностей отказов КМОП ИС, учитывающих влияние ЭСР, и показано, что для электронных измерительных приборов, содержащих относительно небольшое количество таких микросхем, применение стандартизованной модели интенсивностей отказов, учитывающей влияние ЭСР, может привести к существенным погрешностям в расчётах надёжности. В качестве альтернативы предложена модель, ...
Added: October 13, 2016
Zhadnov V. V., Технологии электромагнитной совместимости 2016 № 4 С. 49-52
The considered model of the failure rate of CMOS VHSIC design proposed in the article Piskun G.A., Alekseev V.F., "Improvement of mathematical models calculating of CMOS VLSIC taking into account features of impact of electrostatic discharge", published in the first issue of the journal "Technologies of electromagnetic compatibility" for the year 2016. It is shown ...
Added: October 29, 2016
Kechiev L., М. : Грифон, 2017
Questions of designing of printed-circuit boards for systems of high speed are considered. The basic attention is given maintenance of signal integrity in standard lines TTL/CMOS and in differential pairs. Physical aspects of decrease in level of hindrances in details understand chains of ultrafast devices. Base data on materials for printed-circuit boards, their properties and influence ...
Added: October 26, 2017
Vostrikov A. V., Abrameshin A. E., Технологии электромагнитной совместимости 2012 № 3 С. 22-28
В работе рассмотрены подходы к построению вычислительной схемы ускоренного метода расчета наводок в бортовой кабельной сети космических аппаратов. Показано, что в случае больших эквивалентных электрических схем космических аппаратов для построения вычислительной схемы необходимо решать систему линейных алгебраических уравнений с разреженной блочной матрицей высокого порядка. Учитывая данную специфику, было предложено преобразовать эту матрицу к треугольному виду ...
Added: September 21, 2012
Borisov N., Vostrikov A. V., Krasivskaya M. et al., Технологии электромагнитной совместимости 2014 № 2(49) С. 39-46
The authors developed new reduced computational schemes for the numerical integration of systems of linear differential equations on the basis of methods of Euler. Thus not subjected to the reduction of the original model in the form of a system of linear ordinary differential equations, and mathematical expressions that determine the explicit and implicit methods ...
Added: June 10, 2014
Artyukhova M. A., Polesskiy S., Linetskiy B. et al., Reliability: Theory & Applications 2016 No. 4 P. 84-95
The paper considers the technique of modeling of electronic reliability based on modeling electrical components environment temperature. As experience of the simulation and exploitation of electronic shows, one of the main factors that significantly affect the reliability characteristics is the thermal effect. This is confirmed by the statistics of a number of companies. In the ...
Added: February 28, 2017
Желтов Р. Л., Малов А. В., Першин Е. О. et al., Межотраслевая информационная служба 2013 № 4 С. 59-69
In article relevance of application of computer modeling on the example of subsystems of ASONIKA-T, ASONIKA-M-3D and ASONIKA-TM of the ASONIKA software product for the analysis of standard and nonstandard designs of radio-electronic funds for influence of thermal and mechanical factors is considered. Possibilities of these subsystems are described. The technique of preparation of model ...
Added: January 9, 2014
Kanavets V. I., Mozgovoi Y. D., Khritkin S. A., Известия РАН. Серия физическая 1999 Т. 63 № 12 С. 2333-2339
Added: January 31, 2013
М. : Физический факультет МГУ, 2001
Added: June 15, 2013
Kozhevnikov A., Надежность 2008 № 1 С. 64-71
Рассматривается методология автоматизированного проектирования бортовых радиоэлектронных средств на основе иерархического комплексного системного моделирования. Методология позволяет принимать минимальные по стоимости проектные решения по синтезу допусков и номинальных значений параметров, электрических и тепловых нагрузочных режимов электронных элементов и параметров элементов обеспечения их температурного режима, синтезу систем вибрационной и ударной защиты. Основой методологии являются методы анализа и синтеза ...
Added: October 15, 2013