Разработка методики повышения надежности несущих конструкций радиоэлектронной аппаратуры на этапе проектирования
In article techniques of modeling of radio-electronic equipment in subsystems of ASONIKA-M and АSONIKА-М-IGS are considered, and also the method of increase of reliability of bearing constructions of radio-electronic equipment is described. Examples are resulted.
The article considers the questions assessing the reliability of mechanical components used in the electronic equipment in the early stages of design. The calculations of failure rates springs shock absorbers according to various methods. It is shown that the use of models failure rates of mechanical elements, taking into account the peculiarities of their structural and technological performance, not only allows us to solve the problem of calculating, but also to ensure the required level of reliability and mechanical components, and containing electronic equipment.
The main target of the IEEE East-West Design & Test Symposium (EWDTS-2013) is to exchange experiences between scientists and technologies of Eastern and Western Europe, as well as North America and other parts of the world, in the field of design, design automation and test of electronic circuits and systems. EWDTS’13 covers the following topics:
• Analog, Mixed-Signal and RF Test
• Analysis and Optimization
• EDA Tools for Design and Test
• Failure Analysis, Defect and Fault
• Modeling & Fault Simulation
• Power Issues in Testing
• Reliability of Digital Systems
• Thermal, Timing and Electrostatic Analysis of SoCs and Systems on Board
The monograph presents results by professor Dr. A. Shalumov’s Research School of Modeling, Information Technology and Automated Systems (Russia). The program, ASONIKA, developed by the school is reviewed here regarding reliability and quality of devices for simulation of electronics and chips during harmonic and random vibration, single and multiple impacts, linear acceleration and acoustic noise, and steady-state and transient thermal effects. Calculations are done for thermal stress during changes in temperature and power in time. Calculations are done for number of cycles to fatigue failure under mechanical loads as well as under cyclic thermal effects. Simulation results for reliability analysis are taken into account. Models, software interface, and simulation examples are presented.
For engineers and scientists involved in design automation of electronics.
These are the proceedings of the International Workshop on Petri Nets and Software Engineering (PNSE’13) and the International Workshop on Modeling and Business Environments (ModBE’13) in Milano, Italy, June 24–25, 2013. These are co-located events of Petri Nets 2013, the 34th international conference on Applications and Theory of Petri Nets and Concurrency.
PNSE'13 presents the use of Petri Nets (P/T-Nets, Coloured Petri Nets and extensions) in the formal process of software engineering, covering modelling, validation, and veriﬁcation, as well as their application and tools supporting the disciplines mentioned above.
ModBE’13 provides a forum for researchers from interested communities to investigate, experience, compare, contrast and discuss solutions for modeling in business environments with Petri nets and other modeling techniques.
The basic influencing the factor defining its reliability are temperature influences at which speed of chemical reaction of materials a part REE increases. It is represented the equation which has been received by the Swedish chemist Svante Arreniusom from thermodynamic reasons
This article considers the model of metaphorical transfer of names of natural (atmospheric) phenomena. The worn inner form of many metaphors needs to consult the diachronic aspect, which allowes us to determine the conceptual transfer vector - the emotional attitude of speakers to natural phenomena, deterministic fear of them, faith in their supernatural origin.
Maintenance of reliability of radio-electronic equipment taking into account thermal modes for various classes of electroradioproducts (ERP) within the limits of system ASONIKA is considered.
Generalized error-locating codes are discussed. An algorithm for calculation of the upper bound of the probability of erroneous decoding for known code parameters and the input error probability is given. Based on this algorithm, an algorithm for selection of the code parameters for a specified design and input and output error probabilities is constructed. The lower bound of the probability of erroneous decoding is given. Examples of the dependence of the probability of erroneous decoding on the input error probability are given and the behavior of the obtained curves is explained.
The dynamics of a two-component Davydov-Scott (DS) soliton with a small mismatch of the initial location or velocity of the high-frequency (HF) component was investigated within the framework of the Zakharov-type system of two coupled equations for the HF and low-frequency (LF) fields. In this system, the HF field is described by the linear Schrödinger equation with the potential generated by the LF component varying in time and space. The LF component in this system is described by the Korteweg-de Vries equation with a term of quadratic influence of the HF field on the LF field. The frequency of the DS soliton`s component oscillation was found analytically using the balance equation. The perturbed DS soliton was shown to be stable. The analytical results were confirmed by numerical simulations.
The conference “2021 Systems of signals generating and processing in the field of on board communications” is organized with technical sponsorship of Russian (Moscow) IEEE Circuits and Systems (CAS04) Chapter IEEE Region 8, Russian Section Chapter, MTT/ED and Institute of Radio and Information Systems Association (IRIS), Vienna, Austria. The conference featured invited researchers, educators, managers, and graduate students, whose research activity, case studies or best practices, are shedding light on the theory or practice of engineering, include modern digital transportation systems design and technical operation, radio waves propagation, transmitting, receiving and processing signals in television and radio broadcasting devices, information technologies in transport. The main areas of the conference “Systems of signals generating and processing in the field of on board communications” include modern digital transportation systems design and technical operation, radio waves propagation, transmitting, receiving and processing signals in television and radio broadcasting devices, information technologies in transport. FIELD OF INTEREST: Components, Circuits, Devices and Systems; General Topics for Engineers; Signal Processing and Analysis. Reports presented at the conference are grouped in 6 sections: 1. Antennas and Radio Waves Propagation. 2. Navigation and Mathematical Algorithms of an Object Space Orientation. 3. Radiofrequency Applications. 4. Wire and Optical Communication and Control Systems. 5. Intelligent Transport Systems (ITS): Sub-section 1: Use of digital ITS infrastructure in telematic control systems on urban passenger transport Sub-section 2: Peculiarities of data exchange in cooperative ITS Sub-section 3: Theoretical Aspects of Artificial Intelligence Systems Development for Transportation Engineering Sub-section 4: Test methods of motor vehicles integrated into an intelligent transport environment 6. Digital signal processing in on-board radio systems
Radiation conditions are described for various space regions, radiation-induced effects in spacecraft materials and equipment components are considered and information on theoretical, computational, and experimental methods for studying radiation effects are presented. The peculiarities of radiation effects on nanostructures and some problems related to modeling and radiation testing of such structures are considered.
This volume presents new results in the study and optimization of information transmission models in telecommunication networks using different approaches, mainly based on theiries of queueing systems and queueing networks .
The paper provides a number of proposed draft operational guidelines for technology measurement and includes a number of tentative technology definitions to be used for statistical purposes, principles for identification and classification of potentially growing technology areas, suggestions on the survey strategies and indicators. These are the key components of an internationally harmonized framework for collecting and interpreting technology data that would need to be further developed through a broader consultation process. A summary of definitions of technology already available in OECD manuals and the stocktaking results are provided in the Annex section.