Механические испытания и построение аналитических моделей поведения материалов в условиях сверхпластичности. Часть II
The various test methods for determining the mechanical properties of materials in a state of superplasticity were considered. The tension depends from the deformation and strain rate, the structural parameter and temperature. The rheology and mechanics of superplastic deformation were discusses. Methodology has been tested and gave good results when tested Ti alloys and constructing mathematical models commissioned by EADS (Airbus). Information about the method of testing and subsequent approximation of the mechanical properties is of great interest for the development of adequate forecasts materials forming by pressure.
This paper presents the research of the flow characteristics of the Ti-6V-4Al alloy in wide ranges of temperature (725 ‑ 950 °C) and strain rate (10-5 ‑ 10-2 s-1). The material processing maps were constructed based on the basis of dynamic materials model (DMM) developed by Prassad and modified by Narayana Murty. For the construction of such maps the data of the material’s flow stress at different temperatures and strain rates is necessary. To obtain such data the stepped tensile tests which allow get the stress - strain rate dependence at a given temperature are ideal. The experiments conducted consist of the tensile-testing of samples’ series at various temperatures with stepped change of the deformation speed. By the results of these tests the constitutive equations, which describe relationship between stress and strain rate for each temperature were obtained. The data was analyzed in terms of the two different approaches proposed by Prassad and Narayana Murty to assess the impact of deformation conditions on the formability and flow stability of the material. Based on these approaches, the processing maps which allow identifying the conditions of the Ti-6V-4Al alloy superplasticity were constructed.
The purpose of this study is to find out the characteristics of hot forming of Ti-6Al-4V titanium alloy in order to determine the conditions of its superplastic behavior. Based on experiments conducted in uniaxial tension of flat samples, the stress-strain curves were obtained and examined in a wide range of temperatures and strain-rates. On the base of obtained data, the temperature and strain-rate ranges which ensure the realization of superplasticity at forming of Ti-6Al-4V alloy were determined.
The purpose of this study is to find out the characteristics of hot forming of Ti-6Al-4V titanium alloy in order to determine the conditions of its superplastic behavior. The experiments were performed in two stages: the stepped tensile-tests series (temperature range 700 – 925 °С) and the constant strain rate tensile-test series (temperature range 775 – 925 °С). By the results of stepped tensile tests the constitutive equations which describe relationship between stress and strain rate for each temperature were constructed. On the base of obtained data, the temperature and strain-rate ranges which ensure the realization of superplasticity at forming of Ti-6Al-4V alloy as well as optimal strain rates which corresponds to the maximum value of strain rate sensitivity exponent were determined. In was shown that at low temperatures (700 – 775C) the Ti-6Al-4V alloy shows all signs of superplasticity, however at these temperatures the optimal strain rates are too slow for industrial technological procedures. The dependence between optimum strain rate and reciprocal temperature appears to be well fitted by exponential low. At the second stage of the experimental research, the tensile-tests with a constant, optimum for each temperature strain-rate were carried in order, to estimate the real initial flow stress and the character of strain hardening of the material during the deformation with optimum strain rate. In was found that flow stress values obtained by stepped tensile tests matches the values form constant-strain-rate tests with effective strain value equal to 0,2 and the strain hardening during the deformation with optimal strain rates is significant.
This volume presents new results in the study and optimization of information transmission models in telecommunication networks using different approaches, mainly based on theiries of queueing systems and queueing networks .
The paper provides a number of proposed draft operational guidelines for technology measurement and includes a number of tentative technology definitions to be used for statistical purposes, principles for identification and classification of potentially growing technology areas, suggestions on the survey strategies and indicators. These are the key components of an internationally harmonized framework for collecting and interpreting technology data that would need to be further developed through a broader consultation process. A summary of definitions of technology already available in OECD manuals and the stocktaking results are provided in the Annex section.