?
Detonation Spraying of Ni-Based Composite Coatings Reinforced by High-Entropy Intermetallic Particles
Metals. 2023. Vol. 13. No. 11. Article 1807.
Ostovari Moghaddam A., Shaburova N., Naseri M., Latfulina Y., Samodurova M., Krymsky V., Litvinyuk K.
Ni-based composite coatings reinforced by high-entropy intermetallic compounds (HEICs) were prepared by detonation spraying (DS) on low alloy steel substrates. To this end, first (Ti-Nb)(V-Cr-Ni-Fe) and Al3(TiZrNbCrHfTa) HEIC powders were fabricated by arc melting followed by ball milling. The as-milled HEIC powders were then employed as reinforcement particles to prepare Ni-7wt.% HEIC composite coatings. The average particle size of the (Ti-Nb)(V-Cr-Ni-Fe) and Al3(TiZrNbCrHfTa) HEIC powders were 18 and 35 µm, respectively, while the average particle size of the Ni powder was 56 µm. (Ti-Nb)(V-Cr-Ni-Fe) exhibited a single hexagonal C14 Laves phase in spite of Ti and Nb segregations. The XRD pattern of Al3(TiZrNbCrHfTa) indicated the presence of a tetragonal D022-type structure along with some minor CrTi and Cr5Al8 phases. The sprayed Ni-7wt.% FeNiCrV-TiNb and Ni-7wt.% Al3(TiZrNbCrHfTa) composite coatings retained crystal structures of the powder mixtures, suggesting proper thermal stability for both powders. The coatings exhibited a dense microstructure consisting of a lamellar microstructure with low porosity and sound bonding with the substrate. The microhardness of Ni-7wt.% FeNiCrV-TiNb (450 HV) was higher than that of Al3(TiZrNbCrHfTa) (338 HV), and it exhibited lower fluctuation than that of Ni-7wt.% Al3(TiZrNbCrHfTa). DS is an effective method to fabricate metal matrix composites reinforced by HEICs with a low level of porosity.
Г. Г. Бондаренко, Кристя В. И., Савичкин Д. О. et al., Поверхность. Рентгеновские, синхротронные и нейтронные исследования 2026 № 4 С. 29–36
Сформулирована модель тлеющего газового разряда в смеси аргона и паров ртути при наличии
на поверхности катода тонкой диэлектрической пленки. Рассчитаны зависимости характеристик
разряда от температуры в интервале ее изменения, в котором заметный вклад в ионизацию
рабочей газовой смеси дает ионизация атомов ртути метастабильными возбужденными атомами
аргона (реакция Пеннинга). Показано, что в случае катода без диэлектрической пленки при
повышении температуры до ...
Added: June 20, 2026
Filippova A. V., Yurchenko N. Y., Smirnov S. A. et al., Journal of Alloys and Compounds 2026 No. 1074 Article 189162
This study investigates the effects of post-processing heat treatment at 300–500 °C on the microstructure, hardness, and tensile properties of laser powder bed fusion (PBF-LB) processed Al-bronze processed with energy densities (ED) in the range of 125–938 J/mm3. In the as-printed state, sharp needle-like α + β′ laths form at lower ED whereas with increasing ED, the β′ ...
Added: June 12, 2026
Zirnik G., Ostovari Moghaddam A., Zhukov S. et al., Journal of Materials Science: Materials in Electronics 2026 Vol. 37 Article 738
In regards to the advances in InGaZnO for flexible transistors applications, herein for the first time we measure the broadband radio-frequency range (10 Hz to 1 MHz) dielectric permittivity ε′ and electrical conductivity σ of InGaZnO4 nanoparticle layers at different temperatures ranging from 10 to 300 K. The InGaZnO4 nanoparticles prepared by metal–nitrate–glycol gel decomposition method exhibited ...
Added: June 6, 2026
Das A., Saikia J., Maji N. et al., ChemNanoMat 2026 Vol. 12 No. 5 Article e202500733
Developing efficient photoactive materials from bio-derived resources is vital yet challenging for achieving effective water splitting performance. In this work, nano carbon dots (CDs) of zero-dimensional (0D) were synthesized from papaya peel through a simple and eco-friendly process and subsequently anchored onto the two-dimensional (2D) layered structure of graphitic carbon nitride (g-C3N4, GCN) at various ...
Added: June 2, 2026
Wary R. R., Mahato B., Sharma N. et al., The Journal of Physical Chemistry Letters 2026 Vol. 17 No. 17 P. 5099–5107
Development of heterojunction materials is an efficient approach for enhancing photocatalytic and photoelectrochemical processes. We develop a ZnO/CuO heterojunction via Cu doping into a ZnO matrix. Structural characterization confirmed that Cu was effectively incorporated into ZnO without any structural changes. The improved optical properties and reduced charge carrier recombination of the doped samples were confirmed ...
Added: June 2, 2026
Duran E. ., Pulgar A., Izquierdo R. et al., Physica Status Solidi (A) Applications and Materials 2026 Vol. 223 No. 7 Article e202500942
Ceramic superconductors exhibit remarkable properties, including zero electrical resistance and potent magnetic behavior, operating at temperatures as high as the boiling points of liquid nitrogen (77 K) and liquid hydrogen (20 K). These characteristics position them as key enablers for sustainable technologies spanning electric propulsion, lossless energy transmission, advanced medical imaging, and quantum computation. This review presents ...
Added: June 1, 2026
Андреев Д. В., Корнев С. А., Bondarenko G. et al., Перспективные материалы 2026 № 6 С. 5–11
Выполнено сравнительное исследование процессов сильнополевой зарядовой
деградации подзатворного диэлектрика структур металл-диэлектрик-полупроводник (МДП)
с алюминиевым и поликремниевым затвором. Зарядовые явления в МДП-структурах
изучали методом сильнополевой инжекции электронов в диэлектрик в режиме возрастания
плотности стрессового инжекционного тока с кратковременными переключениями
в измерительный режим при постоянной низкой плотности инжекционного тока.
Использование данного метода позволило получить новые данные о процессах зарядовой
деградации подзатворного диэлектрика МДП-структур с ...
Added: May 21, 2026
Rathish S., Andrey S. Vasenko, Thazhathenair A. et al., The Journal of Physical Chemistry Letters 2026 Vol. 17 No. 18 P. 5386–5394
We demonstrate and rationalize the effect of Au nanoparticles (NPs) on the hierarchical g-C3N4/CeO2 heterojunction. g-C3N4/CeO2 decorated with monodispersed plasmonic Au NPs was synthesized. Detailed analyses showed that CeO2 nanocubes and monodispersed Au NPs were evenly distributed over the 2D g-C3N4 surface, forming a robust interface enriched with abundant active sites. The structure enabled efficient separation of photogenerated charge ...
Added: May 16, 2026
Paul R., Das A., Sharma N. et al., Colloids and Surfaces A: Physicochemical and Engineering Aspects 2026 Vol. 728 Article 138830
Niobium-doped TiO2 (Nb-TiO2), demonstrates dual functionality as an efficient photocatalyst for dye degradation and a promising photoelectrocatalyst for water oxidation. Nb incorporation via a facile hydrothermal method was confirmed by XRD (Rietveld refinement), XPS, TEM, FT-IR, Raman, and BET analyses, indicating successful lattice doping and structural modification. Photocatalytic dye degradation experiments were conducted using a model ...
Added: May 16, 2026
Гущина В. А., / Series chemrxiv-2023-vpzhz-v2 "ChemRxiv". 2023.
All-inorganic perovskite CsPbBr3 and Cs4PbBr6 nanoparticles are being intensively studied due to their unique properties and wide range of applications; however, however, the nature of their optical properties is not yet fully understood due to the difficulty of synthesis of singlephase nanoparticles. In this article we describe the features of the synthesis of single-phase particles ...
Added: May 14, 2026
Гущина В. А., Mendeleev Communications 2025 Vol. 35 No. 2 P. 193–195
All-inorganic perovskite CsPbBr3 and Cs4PbBr6 nanoparticles are intensively studied for their unique optical properties, though synthesizing single-phase nanoparticles has posed challenges. Detailed synthesis method of CsPbBr3 and Cs4PbBr6 single-phase nanoparticles and their chemical and phase analysis are described. Distinctive optical characteristics, such as photoluminescence, optical band gap and the Urbach tail region, are revealed and explained within the current ...
Added: May 14, 2026
Гущина В. А., Physics of Complex System 2026 Vol. 7 No. 1 P. 3–15
Heterostructures based on ZnO nanorods and CsPbBr3 nanocrystals were investigated for their potential as semiconductor SERS substrates. We found that ZnO morphology governs the efficiency of interfacial energy transfer, leading to enhanced photoluminescence under 390 nm excitation and a noticeable reduction of the bandgap in the composites. Raman analysis revealed a pronounced intensity enhancement and ...
Added: May 14, 2026
Гущина В. А., Russian Journal of Inorganic Chemistry 2024 Vol. 69 No. 6 P. 940–948
Currently, ABX3 nanoparticles (NPs) based on lead halides attract the attention due to their unique optical properties and a wide range of applications. The preparation of NPs with lead as a partial or complete replacement is particularly interesting because of the toxicity of this chemical element and most of its compounds. In this study, we propose a ...
Added: May 6, 2026
Yasnitsky L., Голдобин М. А., Мезенцев А. С., Прикладная математика и вопросы управления 2025 № 2 С. 99–116
Представлен обзор современных методов и основанных на них программных
инструментах, применяемых для математического моделирования серийных производственных процессов с целью снижения брака и повышения качества производимых изделий. Перечисляются группы работ, нацеленных на обнаружение и классификацию дефектов, работ, в которых решаются задачи прогнозирования образования дефектов и определения значимости параметров, работ направленных на поиск
оптимального сочетания технологических параметров изготовления изделий, ...
Added: May 5, 2026
Morozov E. V., Demin A. S., Borovitskaya I. V. et al., Inorganic Materials: Applied Research 2026 Vol. 17 No. 3 P. 619–626
This article presents the results of experiments on the impact of powerful pulsed ion-plasma and
electron flows generated in the working chamber of the Plasma Focus PF-5M installation during each highvoltage
discharge on a model aluminum alloy B95. It is shown that the general characteristics of the alloy’s
damage upon exposure to pulsed flows of helium ions (HI) ...
Added: May 4, 2026
Pavlenko V. I., Bondarenko G.G., Cherkashina N. I. et al., Inorganic Materials: Applied Research 2026 Vol. 17 No. 2 P. 276–282
A composite material based on polyethylene, boron carbide (B4C), and bismuth oxide (Bi2O3) is
synthesized by the method of joint cryogenic milling of all components in liquid nitrogen environment followed
by pressing. The effect of cryogenic milling on the distribution of fillers in a composite is studied and
the prospects of using this method are assessed in comparison ...
Added: April 9, 2026
Черкашина Н. И., Павленко В. И., Bondarenko G. et al., Перспективные материалы 2026 № 4 С. 14–26
В данной работе представлен синтез гибкого полимерного композита для защиты от радиации на основе каучуковой матрицы и оксидов редкоземельных металлов, таких как Dy2O3 и Gd2O3, предназначенного для создания радиационно-защитных экранов и средств индивидуальной защиты. Исследованы его физико-механические характеристики: составы с добавлением оксида диспрозия имеют плотность от 1,31 до 2,44 г/см3, предел прочности при растяжении от ...
Added: April 2, 2026
Chowde Gowda C., Alexey Kartsev, Tiwari N. et al., Journal of Materials Chemistry C 2024 Vol. 12 No. 46 P. 18691–18703
Two-dimensional (2D) chromium telluride Cr2Te3 exhibits strong ferromagnetic ordering with high coercivity at low temperatures and paramagnetic behavior when approaching room temperature. The spin states of monolayer Cr2Te3 show ferromagnetic ordering in the ground state. In situ Raman analysis reveals a reversible structure transformation and hence proves ferromagnetic to paramagnetic transition during low-temperature heating cycles (0–25 °C). The magnetic ...
Added: March 16, 2026
Petrakova N., Demina A., Zobkova Y. et al., Journal of Alloys and Compounds 2025 Vol. 1037 Article 181865
The hydroxyapatite powders with co-doping of Ca2+ with Na+ and Ce3+ were obtained by aqueous precipitation.
Co-doping was considered as a method of charge compensation in the cationic sublattice of the HA structure by
means of the 2Ca2+→Ce3+ + Me+ in order to maintain the stability of phase composition, improve the optical
and microstructural properties of the HA ...
Added: November 5, 2025
Ostovari Moghaddam A., Shaburova N. A., Mikhailov D. et al., Journal of Chemical Technology and Metallurgy 2025 Vol. 60 No. 4 P. 645–652
AlCoCrFeNi2.1 eutectic high entropy alloy (HEA)composite coatings reinforced by Al2O3 particles were prepared by detonation spraying (DS) on low alloy steel substrates. The effect of annealing at different temperatures on the microstructure and mechanical properties of the coatings was further studied. The as-deposited AlCoCrFeNi2.1 - 30 wt. % Al2O3 composite coating exhibited a dual-phase FCC+BCC ...
Added: August 29, 2025
Samoilova O., Pratskova S., Shaburova N. et al., Materials 2025 Vol. 18 No. 15 Article 3701
The microstructure, phase composition, and high-temperature oxidation resistance of Fe-free AlCoCrNiNb0.2 and AlCoCr0.5NiNb0.2 high-entropy alloys (HEAs) were investigated. In the as-cast HEAs, niobium was found to mainly release as a Laves phase in the interdendritic region, and its solubility in the dendrites of the BCC solid solution was about 2 at.%. Both samples exhibited parabolic behavior during ...
Added: August 29, 2025
Ostovari Moghaddam A., Shaburova N., Abdollahzadeh A. et al., Journal of Alloys and Compounds 2025 Vol. 1035 Article 181537
In this study, an off-stoichiometric boron-doped chemically complex intermetallic alloy with a dual phase ordered-L12/disordered-FCC structure was developed, which exhibited an outstanding combination of high strength and ductility. The superior mechanical properties were attributed to the synergistic features of dual-phase microstructure, increased antiphase boundary energy due to the multi-additions of Ti, Nb and Ta elements ...
Added: June 30, 2025
Nechvoglod O., Ostovari Moghaddam A., Pratskova S. et al., The Minerals, Metals & Materials Society 2025 Vol. 77 P. 1005–1028
This work provides an overview on the fabrication process, composition and properties of high-entropy alloy (HEA) coatings fabricated by electrodeposition. Special attention is paid to the effect of electrodeposition parameters and electrolyte composition on the microstructure, morphology, and mechanical/functional properties of the HEA coatings. It is demonstrated that the majority of researches has been focused ...
Added: June 10, 2025
Дудников Д. О., Коннов Э. А., Огурцов Н. А., Вестник Астраханского государственного технического университета. Серия: Управление, вычислительная техника и информатика 2025 Т. 2025 № 2 С. 69–75
Представлены современные подходы к автоматизации анализа микроструктуры металлических материалов, направленные на повышение точности и эффективности исследований. Описана разработка программного обеспечения для идентификации и классификации зерен в металлах, что является ключевым аспектом в изучении их структуры и прогнозировании механических свойств. Программа включает модули для частично автоматизированной обработки изображений, анализа характеристик зерен, визуализации результатов и интеграции с ...
Added: May 15, 2025